Mada za sehemu hiiPerforming cuttingMada 3
- Performing straight sawing
- Performing angular sawing
- Performing chiseling
Straight Sawing

Straight sawing (also called vertical sawing) is the process of cutting a material in a straight line without any angles or deviations. The purpose is to divide a material into two or more pieces. This skill is essential in electronics repair and fabrication when you need to cut metal, plastic, or other materials into specific sizes for making components, brackets, or trunkings.
The main tool for straight sawing is a hacksaw, which has two parts:
- Hacksaw blade – the cutting toothed blade
- Hacksaw frame – the holder that stretches and supports the blade
Other supporting tools include:
- Steel rule (for measuring)
- Scriber (for marking)
- Centre punch (for marking)
- Back square or T-square (for checking right angles)
- Hammer (for using with centre punch)
- Vice (to hold the workpiece firmly)
Step 1: Select the Correct Blade
Choose a blade suitable for the material you are cutting. Different blades have different tooth sizes (teeth per inch). Finer teeth are used for thin metals, while coarser teeth work better for thicker materials.
Step 2: Mount the Blade
- Hook the blade over the pin at the end of the frame
- Attach the other end to the pin in the handle
- Ensure the teeth point away from the handle – the saw cuts only on the forward stroke
Step 3: Set the Blade Tension
- Tighten the wing nut to take up tension
- Turn it another two full turns
- Do not overtighten – this can break the pins or bend the frame
- A new blade stretches slightly, so retighten after the first few strokes
Step 1: Prepare the Workpiece
- Measure and mark the workpiece using a steel rule and scriber
- Clamp the workpiece firmly in the vice
- Cut as close to the vice as possible to reduce vibration
Step 2: Position Yourself Correctly
- If you are right-handed, cut on the right-hand side of the vice
- If you are left-handed, cut on the left-hand side
- This ensures that if the blade breaks, your hands will slip away from the vice, not into it
Step 3: Start the Cut
- Use your thumb to guide the blade at the start of the cut
- Hold the hacksaw at about a 45-degree angle to the workpiece
- Apply pressure only on the forward stroke
- Release pressure on the return stroke
Step 4: Maintain Steady Cutting
- Keep the cutting speed at 40 to 50 strokes per minute
- Use the whole length of the blade for even wear
- Apply constant pressure on the forward stroke to keep the cut even
- Distribute your body mass evenly to stay balanced
Step 5: Complete the Cut
- When the blade has almost cut through, support the piece with your hand
- This prevents it from dropping and causing injury or damage
- Always wear safety glasses, gloves, safety boots, and overall
- Keep the blade dry to prevent rust
- Lubricate the blade with oil when cutting metal to prevent overheating
- Inspect blades regularly for damage or dullness and replace when necessary
- Always switch off power before maintaining electric cutting tools
A student has a flat bar of 10 mm × 200 mm mild steel and needs to cut it into six pieces of approximately 30 mm each.
Procedure:
- Measure the flat bar using a steel rule and mark six segments of 30 mm each with a scriber
- Select a hacksaw blade suitable for cutting mild steel (medium tooth size)
- Mount the blade on the hacksaw frame with teeth pointing away from the handle
- Tighten the wing nut until the blade is taut, then give two more full turns
- Clamp the workpiece firmly in the vice, with the first mark close to the vice jaws
- Cut along the first marked line using steady forward strokes, keeping the saw at 45 degrees
- Support the piece as it separates to prevent it from falling
- Repeat for all five remaining cuts
- Clean the workpiece and store tools properly
In Tanzania, straight sawing is a practical skill used by bicycle repair mechanics in local workshops. When a broken bicycle frame needs shortening or a rusty pedal arm requires cutting for replacement, the mechanic uses a hacksaw to make precise straight cuts on metal parts. This enables quick repairs at low cost, helping community members get their bicycles back in working condition without needing expensive new parts.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret drawings
- Select tools and equipment
- Take measurements
- Cut work piece
- Check for accuracy
- Observe safety precautions
- Clean tools, work piece and workplace
- Store tools, equipment and materials in a designated storage area.
Tathmini ya matokeo
Pieces of material cut as per technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to cut work piece in different sizes
Principles: The student should explain the principles of:
- Taking measurements
- Marking work piece
- Cutting process
Theories: The student should explain:
- Different types of materials and their properties
- Application of different cutting tools
- Uses of cutting tools and equipment
- Use of measuring tools
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing the cutting process
- Safe handling of work tools and equipment
- Waste disposal
Swali
What is the primary tool used for performing straight sawing in electronics repair?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado