Mada za sehemu hiiPerforming cuttingMada 3
- Performing straight sawing
- Performing angular sawing
- Performing chiseling
Performing angular sawing
Angular sawing is the process of cutting a material at an angle other than a straight 90-degree cut. This technique is essential when you need to create mitered joints, chamfered edges, or angled components in metalwork. Like straight sawing, angular sawing uses a hacksaw, but the workpiece must be marked and positioned at the required angle before cutting.
Before performing angular sawing, gather the following tools:
- Hand hacksaw with blade
- Steel rule
- Scriber
- Vernier caliper
- Bevel protractor
- Mallet
- Vice
The bevel protractor is particularly important for angular sawing because it measures and transfers angles accurately onto the workpiece.
Step 1: Interpret the drawing
Study the working drawing to understand the required angle and dimensions of the cut. Identify whether you need to cut at 30°, 45°, or another angle as specified.
Step 2: Select and prepare the workpiece
Select a flat bar of appropriate size, such as a 10 mm × 30 mm × 60 mm mild steel piece. Ensure the workpiece is clean and free from rust or debris.
Step 3: Mark the workpiece
Use the steel rule, scriber, and bevel protractor to mark the material to be cut. Measure the desired angle carefully and draw the cutting line using the scriber. The bevel protractor allows you to set and transfer the exact angle required.
Step 4: Clamp the workpiece
Secure the workpiece firmly in the vice. Position it so that the marked cutting line is accessible and angled correctly relative to the hacksaw blade. The workpiece should be clamped close to the cutting line to minimize vibration.
Step 5: Perform angular sawing

Hold the hacksaw at the angle corresponding to your marked line. Apply pressure only on the forward stroke and release pressure on the return stroke, just as in straight sawing. The blade should cut along the marked angle line. Use the whole length of the blade and maintain a steady pace of about 40 to 50 strokes per minute.
Step 6: Complete and clean up
Once the cut is complete, untighten the vice and remove the workpiece. Clean the working area and store all tools in their proper positions.
Always wear safety gear including safety glasses, gloves, safety boots, and overalls when performing angular sawing. Cut on the correct side of the vice—right side for right-handed persons and left side for left-handed persons—to prevent injury if the blade breaks. Ensure the hacksaw blade is properly tensioned but not overtightened.
A student needs to cut a 10 mm × 30 mm mild steel flat bar at 45° to make a corner frame piece. The student:
- Marks a 45° angle using a bevel protractor on the workpiece
- Draws the cutting line with a scriber
- Clamps the workpiece firmly in the vice with the marked line positioned at 45° to the hacksaw blade
- Cuts along the line, applying steady forward pressure
- Produces a clean 45° angled cut for the frame
This process follows the same technique as straight sawing, but the workpiece is positioned at the required angle before cutting begins.
- Failing to use a bevel protractor may result in inaccurate angles
- Cutting too fast can overheat the blade and cause blunting
- Improper clamping causes vibration and uneven cuts
- Not supporting the workpiece near the cut can cause it to fall and be damaged
In Tanzania, angular sawing is used by electronics repair technicians and artisans when fabricating metal enclosures, mounting brackets, or cable trunking that require angled joints. For example, when installing a security alarm system, a technician may need to cut a metal trunking at a 45° angle to neatly route cables around a corner wall, ensuring a professional and tidy installation.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret drawings
- Select tools and equipment
- Take measurements
- Cut work piece
- Check for accuracy
- Observe safety precautions
- Clean tools, work piece and workplace
- Store tools, equipment and workplace
Tathmini ya matokeo
Pieces of material cut as per technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to cut work piece in different sizes
Principles: The student should explain the principles of:
- Taking measurements
- Marking work piece
- Cutting process
Theories: The student should explain:
- Different types of materials and their properties
- Application of different cutting tools
- Uses of cutting tools and equipment
- Use of measuring tools
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while performing cutting process
- Safe handling of work tools and equipment
- Waste disposal
Swali
What is angular sawing?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado