Mada za sehemu hiiMeasuring electric quantitiesMada 3
- Measuring voltage in the circuit
- Measuring current in the circuit
- Measuring resistance in the circuit
Voltage is the "push" that makes electric charges move through a circuit. Without voltage, current cannot flow, and electrical components will not work.
Voltage is the electrical pressure or potential difference between two points in a circuit. It is measured in Volts (V), named after Alessandro Volta, the inventor of the first battery.
Think of voltage like water pressure in a pipe. The higher the pressure, the more water can flow. Similarly, higher voltage pushes more electric current through a circuit.
Voltage has three important roles:
- Provides energy — voltage supplies the energy that moves electrons through conductors
- Determines component operation — each component (resistor, LED, capacitor) requires a specific voltage to work properly
- Controls current — according to Ohm's Law, for a fixed resistance, increasing voltage increases current: I=RV
A circuit needs the correct voltage. Too little voltage and components won't work. Too much voltage and components can be damaged.
A multimeter is a tool that measures voltage, current, and resistance. Follow these steps:
Step 1: Prepare the Multimeter
- Turn the dial to the voltage setting (V) — choose DC (⎓) or AC (∿) depending on your power source
- If using an analog meter, calibrate the zero adjustment
- Insert the black lead into the COM (common) jack
- Insert the red lead into the V/Ω jack
Step 2: Connect the Multimeter to the Circuit
- Always connect in parallel — place the multimeter leads across the component you want to measure
- Connect the black lead to the negative side of the component
- Connect the red lead to the positive side of the component
- Do not disconnect the component; just touch the leads to the points you want to measure
Step 3: Read the Measurement
- Turn on the circuit power (if not already on)
- Read the voltage value displayed on the screen
- Record the reading with its unit (Volts)
Step 4: Safety Tips
- Always start with a higher voltage range and adjust lower if needed
- Never touch bare wires while circuit is powered
- Wear safety gloves and boots when working with live circuits
A student builds a simple circuit with a 9V battery connected to a resistor. The student places the multimeter probes across the resistor and obtains a reading of 4.5V.
Question: What is the voltage drop across the resistor?
Answer: The voltage drop across the resistor is 4.5V. This means the resistor is using 4.5V of the total 9V supplied by the battery. The remaining 4.5V would appear across other components in the circuit (if any).
This demonstrates an important rule: in a series circuit, the sum of all voltage drops equals the total supply voltage: Vtotal=V1+V2+V3+...
- Voltage is measured in Volts (V)
- Always connect the multimeter in parallel to measure voltage
- Black lead goes to the negative (lower potential)
- Red lead goes to the positive (higher potential)
- Start with a higher range on the multimeter for safety
- Voltage across a component is called a "voltage drop"
In Tanzania, voltage measurement is essential when repairing mobile phone chargers or checking car battery health. For example, a technician at a workshop in Mwanza checking a 12V car battery would use a multimeter to measure if the battery is still holding charge — if the voltage reads below 12.4V when the engine is off, the battery needs charging or replacement, helping drivers avoid being stranded.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Determine component values
- Connect simple electric circuits
- Perform soldering
- Measure electric quantities
- Record measured values
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
Recorded values conform to standard values.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure components values
- Measure values of voltage in circuit
Principles: The student should explain the principle of:
- Reading colour codes
- Performing soldering
- Measuring electric quantities
Theories: The student should explain:
- Ohm’s law
- Different component ratings
- Types of electric circuit connections
- Verification of electric rules and laws
- Importance of component ratings
- Types and uses of measuring equipment
- Application of colour codes
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of working tools
- Safe handling of measuring instruments.
Swali
What unit is voltage measured in?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado