Mada za sehemu hiiMeasuring electric quantitiesMada 3
- Measuring voltage in the circuit
- Measuring current in the circuit
- Measuring resistance in the circuit
Measuring Resistance in the Circuit
Resistance is the opposition that a material offers to the flow of electric current. It is measured in ohms, symbolized by the Greek letter omega (Ω). Every component in a circuit — including wires, resistors, and other parts — has some resistance. Understanding resistance helps us control how much current flows through a circuit.
Resistance plays several important roles:
- Current control: Resistors limit the amount of current flowing through a circuit, protecting sensitive components from damage.
- Voltage division: Resistors are used in voltage divider circuits to obtain specific voltage levels.
- Heat generation: Some devices, like electric cookers and irons, use resistance to produce heat.
- Signal adjustment: In electronic devices, resistors help shape and control signals.
The main instrument used to measure resistance is a multimeter. A multimeter can be:
- Analog — uses a needle and scale to display readings
- Digital — shows the reading as a number on a display
Both types can measure resistance, but digital multimeters are easier to read and more commonly used today.
Follow these steps carefully:
- Turn off the power — Always disconnect the component or circuit from any power source before measuring resistance. Otherwise, you may get an incorrect reading or damage the multimeter.
- Select the resistance mode — Turn the multimeter dial to the resistance setting (usually marked with "Ω").
- Choose the appropriate range — If your multimeter has manual range selection, start with a higher range and switch to a lower one for better accuracy.
- Connect the probes — Insert the black probe into the COM (common) jack and the red probe into the Ω jack. Touch the probe tips to both ends of the component being measured.
- Read the display — On a digital multimeter, read the value shown on the screen. On an analog meter, read the value where the needle stops on the scale.
- Record your reading — Note the measured value and compare it with the expected (labelled) value.
A student is given a resistor with colour bands showing a labelled value of 1,000 ohms (1 kΩ). The student connects the multimeter probes to the resistor leads and obtains a reading of 980 Ω.
Question: Is this resistor within an acceptable range?
Answer: Yes. The measured value of 980 Ω is close to the labelled value of 1,000 Ω. The small difference (20 Ω or 2%) is normal and falls within the tolerance of most resistors. This means the resistor is functioning correctly.
- Ensure good contact between the probes and the component leads.
- Avoid touching the metal parts of the probes while measuring, as your body resistance can affect the reading.
- Check the probes and leads for damage before use.
- If measuring a resistor in a circuit, disconnect one end of the resistor from the circuit to get an accurate reading.
When working with electronics:
- Always wear safety gloves and safety boots when handling live or potentially live components.
- Make sure the work bench is clear and well-lit.
- Never measure resistance on a live circuit — always disconnect power first.
In Tanzania, technicians use multimeters to test resistors in everyday devices such as phone chargers, radios, and solar panel controllers. For example, if a radio stops working in a village shop, a local repair technician can use a multimeter to quickly check whether a resistor inside the radio has failed, saving the cost of replacing the entire device.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Determine component values
- Connect simple electric circuits
- Perform soldering
- Measure electric quantities
- Record measured values
- Clean tools, equipment and workplace
- Store tools and equipment
Tathmini ya matokeo
Recorded values conform to standard values.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure components values
- Measure values of resistance in circuit
Principles: The student should explain principle of:
- Reading colour codes
- Performing soldering
- Measuring electric quantities
Theories: The student should explain:
- Ohm’s law
- Different component ratings
- Types of electric circuit connections
- Verification of electric rules and laws
- Importance of component ratings
- Types and uses of measuring equipment
- Application of colour codes
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of working tools
- Safe handling of measuring instruments.
Swali
What is the SI unit of electrical resistance?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado