Mada za sehemu hiiDetermining characteristics of active electronic devicesMada 5
Transistor Testing
A transistor is a small electronic component made of semiconductor material that can control current flow. It has three terminals called the base, collector, and emitter. Before using a transistor in a circuit, we must test it to ensure it works properly and identify whether it is an NPN or PNP type.
There are two main types of bipolar junction transistors (BJTs):
- NPN Transistor – Current flows from collector to emitter when the base receives a small current
- PNP Transistor – Current flows from emitter to collector when the base receives a small current
The letter designations (N and P) refer to the type of semiconductor material used.
Transistors have three legs that must be correctly identified before testing. Using a multimeter:
- Set the multimeter to diode testing mode (or resistance mode)
- Touch the red lead to one terminal and black lead to each of the other two terminals
- The terminal that gives a reading with both other terminals is likely the base
- If the meter shows a forward voltage drop (0.5V – 0.7V) from base to the other two terminals, you have an NPN transistor
- If the meter shows a forward voltage drop when the black lead is on the base, you have a PNP transistor
Procedure
-
Safety first – Wear gloves and overalls. Ensure the work bench is clean and free of metal objects.
-
Set your digital multimeter to the diode test function.
-
Identify the transistor type (NPN or PNP) as described above.
-
For NPN transistor testing:
- Connect the red (positive) multimeter lead to the base
- Touch the black (negative) lead to the collector – meter should show 0.5V to 0.7V
- Touch the black lead to the emitter – meter should show 0.5V to 0.7V
- Reverse the leads (red to collector, black to base) – meter should show OL (open loop)
- Repeat with red to emitter, black to base – should also show OL
-
For PNP transistor testing:
- Connect the black lead to the base
- Touch the red lead to the collector – meter should show 0.5V to 0.7V
- Touch the red lead to the emitter – meter should show 0.5V to 0.7V
- Reverse the leads – meter should show OL
Worked Example
You have an NPN transistor and your multimeter shows the following readings:
| Test Points | Reading |
|---|---|
| Base (+) to Collector (−) | 0.65 V |
| Base (+) to Emitter (−) | 0.62 V |
| Collector (+) to Base (−) | OL |
| Emitter (+) to Base (−) | OL |
Interpretation: These readings are normal. The forward voltage drops (0.62V and 0.65V) show healthy base-emitter and base-collector junctions. The OL readings show the junctions are not conducting in reverse direction. Conclusion: The transistor is good.
Signs of a Faulty Transistor
- Shorted junction – Meter shows 0V or very low resistance in both directions
- Open junction – Meter shows OL in both directions when testing base-to-others
- Leaky transistor – Meter shows a low voltage reading (less than 0.3V) in both forward and reverse directions
- Identify the transistor type (NPN or PNP) using diode test
- Check base-collector and base-emitter junctions for correct forward voltage drop
- Verify reverse direction shows OL (open)
- Compare readings to determine if transistor is functional or faulty
- Always disconnect power before testing
- Keep your work area organized
- Handle transistors carefully – they are sensitive to static electricity
- Wear protective clothing as required
In Tanzania, transistor testing is used when repairing radio receivers, mobile phone chargers, and sound systems found in homes and small shops. For example, when a radio stops working in Morogoro, an electronics repair technician uses a multimeter to test the transistors inside the radio, identifies which one is faulty, and replaces it so the radio plays again.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Select electronic components
- Construct circuit for component testing
- Test electronic component
- Record test results
- Interpret standard test results
- Observe safety regulations
- Clean tools, equipment and workplace
- Store tools, equipment and components
Tathmini ya matokeo
Tested components bear characteristics that conform to specifications as given in component data books.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to test components
Principles: The student should explain the principles of:
- Operating test equipment and measuring instruments
- Testing components
Theories: The student should explain:
- Types of active electronic components
- The difference between passive and active electronic components
- Characteristics of active electronic components
- Variation of component performance with temperature
Circumstantial knowledge:
Detailed knowledge about: Safety precautions in electronic work
- Safe handling of tools, test equipment and measuring instruments
- Safe handling of electronic components.
Swali
What are the three terminals of a bipolar junction transistor (BJT)?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado