Mada za sehemu hiiDetermining characteristics of active electronic devicesMada 5
A thyristor (also called SCR - Silicon Controlled Rectifier) is a semiconductor device that acts like a switch. It has three terminals: Anode (A), Cathode (K), and Gate (G). Once triggered, it conducts current from anode to cathode and stays "ON" until the current through it drops to zero. Thyristors are widely used in power control systems such as light dimmers, motor speed controls, and voltage regulators.
Before using a thyristor in a circuit, we must check that it works properly. Testing tells us:
- Whether the device blocks forward voltage when it should (OFF state)
- Whether it can be turned ON by a gate signal
- Whether it blocks reverse voltage correctly
Before testing, identify the three terminals:
- Anode (A) – usually connected to the positive side of the circuit
- Cathode (K) – usually connected to the negative side
- Gate (G) – the control terminal that triggers the device ON
Look at the component marking. Most thyristors have the terminals labelled or arranged in a specific pattern. If unsure, refer to the datasheet.
- Set the multimeter to resistance mode (Ω) or diode test mode.
- Connect the positive lead to the Anode and the negative lead to the Cathode.
- Observe the reading:
- A good thyristor should show high resistance (no continuity) — typically several kilo-ohms or "OL" (over limit).
- If it shows low resistance or beeps (continuity), the thyristor is faulty (internal short circuit).
This test confirms that the thyristor blocks forward current when it is not triggered — this is the forward blocking state.
- Reverse the connections: positive lead to Cathode, negative lead to Anode.
- Observe the reading:
- A good thyristor should show high resistance (or "OL") — it blocks reverse voltage.
- If it shows low resistance, the device is damaged.
- Start with the multimeter leads connected as in the forward blocking test (positive to Anode, negative to Cathode). The reading should show high resistance.
- Use a separate low-voltage DC source (such as a 1.5V battery or a function generator) or a momentary switch connected between the Gate and Cathode.
- Apply a short pulse by touching the Gate terminal to the positive of the DC source for a moment, then remove it.
- Quickly check the multimeter reading again:
- A working thyristor will now show low resistance (or beep) between Anode and Cathode — it has been triggered "ON".
- The resistance should stay low even after removing the gate signal, because the thyristor is now latched.
If the resistance stays high after the gate pulse, the thyristor cannot be triggered and is faulty.
Scenario: You have a thyristor labelled BT151. You need to test if it is functional.
Step 1: Identify terminals. For BT151, the terminal order (from left to other side) is Anode – Gate – Cathode.
Step 2: Test forward blocking. Set multimeter to 20kΩ range. Red lead to Anode, black lead to Cathode. The display shows 12 kΩ (or OL). Result: PASS — it blocks forward voltage.
Step 3: Test reverse blocking. Red lead to Cathode, black lead to Anode. The display shows OL. Result: PASS — it blocks reverse voltage.
Step 4: Trigger the thyristor. With leads still as in Step 2 (red to Anode, black to Cathode), touch a 1.5V battery's positive terminal to the Gate for one second, then remove. Quickly observe the multimeter. It now shows 120 Ω. Result: PASS — the thyristor turned ON and latched.
Conclusion: The thyristor is good and can be used in a circuit.
- Always wear gloves and an overcoat when handling components and power supplies.
- Ensure the power supply is set to low voltage (below 12V) for testing.
- Do not touch live circuits while testing.
- Work at a safe work bench and wear boots for protection.
In Tanzania, thyristors are used in voltage regulators for street lights and in rice milling machines where motor speed needs to be controlled. If a technician repairs a faulty light dimmer or speed controller, they must test the thyristor to confirm it is working before replacing other expensive parts — this saves both time and money, especially in small repair shops in towns like Arusha or Mwanza.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Select electronic components
- Construct circuit for component testing
- Test electronic component
- Record test results
- Interpret standard test results
- Observe safety regulations
- Clean tools, equipment and workplace
- Store tools, equipment and components
Tathmini ya matokeo
Tested components bear characteristics that conform to specifications as given in component data books.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to test components
Principles: The student should explain the principles of:
- Operating test equipment and measuring instruments
- Testing components
Theories: The student should explain:
- Types of active electronic components
- The difference between passive and active electronic components
- Characteristics of active electronic components
- Variation of component performance with temperature
Circumstantial knowledge:
Detailed knowledge about: Safety precautions in electronic work
- Safe handling of tools, test equipment and measuring instruments
- Safe handling of electronic components
Swali
What are the three terminals of a thyristor (SCR)?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado