Mada za sehemu hiiUsing of oscilloscopeMada 3
- Displaying low frequency signal
- Displaying high frequency signal
- Measuring voltage, current and frequency
Measuring voltage, current, and frequency are fundamental skills in electronics repair. These quantities tell us how electrical energy is being used in a circuit, and comparing measured values with expected values helps us find faults.
Voltage is the electrical pressure that pushes current through a circuit. It is measured in volts (V).
Using a Multimeter to Measure Voltage
- Set the multimeter dial to the appropriate AC (V~) or DC (V⎓) voltage range. Choose a range higher than the expected voltage.
- Insert the black lead into the COM (common) socket.
- Insert the red lead into the VΩmA socket.
- Touch the black probe to the negative or ground point of the circuit.
- Touch the red probe to the positive point where you want to measure voltage.
- Read the voltage value displayed on the screen.
Key Points for Voltage Measurement
- Always measure voltage across (parallel to) a component.
- Never touch bare wires or terminals while measuring.
- If the display shows "1" or "OL", the voltage is higher than the selected range — switch to a higher range.
Current is the flow of electric charge through a circuit. It is measured in amperes (A) or milliamperes (mA).
Using a Multimeter to Measure Current
- Set the multimeter dial to the appropriate current range (A~ for AC or A⎓ for DC).
- Insert the black lead into the COM socket.
- Insert the red lead into the 10A socket (for currents up to 10A) or the mA socket (for smaller currents).
- Break the circuit at the point where you want to measure current.
- Connect the black probe to one side of the break and the red probe to the other side, so current flows through the multimeter.
- Read the current value displayed on the screen.
Key Points for Current Measurement
- Current must be measured in series (in line) with the component.
- Always start with the highest current range to avoid damaging the meter.
- Return the leads to the voltage sockets after measuring current.
Frequency is the number of complete cycles of an AC signal per second. It is measured in hertz (Hz).
Using a Frequency Counter or Multimeter with Frequency Function
- If using a multimeter with a frequency (Hz) function, set the dial to Hz.
- Connect the black lead to the circuit ground.
- Connect the red lead to the signal source or test point.
- Read the frequency displayed on the screen.
Using an Oscilloscope for Frequency
- Connect the oscilloscope probe to the test point.
- Adjust the vertical (Y) and horizontal (X) controls to display a stable waveform.
- Count the number of complete cycles visible on the screen.
- Use the time-per-division setting to calculate the period (T) of one cycle, then calculate frequency using the formula:
f=T1
where f is frequency in hertz and T is the period in seconds.
A signal generator is connected to a circuit. An oscilloscope displays a waveform that completes 5 complete cycles in 10 milliseconds across the screen. What is the frequency of the signal?
Solution
First, find the period of one cycle:
Total time for 5 cycles = 10 ms = 0.01 s
T=50.01 s=0.002 s=2 ms
Now calculate the frequency:
f=T1=0.002 s1=500 Hz
The signal frequency is 500 Hz.
- Always wear protective gloves and an overcoat or overall when working with electrical equipment.
- Ensure the work bench is clean and dry.
- Never measure voltage or current on live circuits unless instructed — always turn off power before connecting leads for current measurement.
- Use boots to insulate yourself from the floor.
In Tanzania, these measurement skills are used when repairing radio receivers, phone chargers, and solar panel systems commonly found in homes and schools. For example, a technician at a small electronics shop in Mwanza might use a multimeter to check that a phone charger is producing the correct 5V output before selling it, or measure the frequency of a generator to ensure it is running at the proper 50 Hz (the standard frequency in Tanzania's power grid).
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Use oscilloscope
- Calibrate oscilloscope
- Observe safety regulations
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Oscilloscope displays measured quantities as per technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to use oscilloscope
Principles: The student should explain the principles of:
- Setting oscilloscope
- Measuring electrical quantities using oscilloscope
Theories: The student should explain:
- Parts of oscilloscope
- Application of oscilloscope
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions while using oscilloscopes
- Safe handling of test equipment
Swali
When measuring voltage across a resistor using a multimeter, how should the probes be connected?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado