Mada za sehemu hiiHandling fire accidentsMada 3
- Performing fire classification
- Performing firefighting
- Performing fire protection
Performing Firefighting
Fire is a rapid chemical reaction that releases heat, light, and smoke. Understanding how fires start and how to extinguish them is essential for safety in any workplace, including solar power installation workshops. This note teaches you the basic methods of firefighting so you can respond quickly and safely in case of a fire accident.
The Fire Triangle

Fire requires three elements to burn. These three elements form what is called the fire triangle:
- Fuel – any material that can burn (wood, paper, petrol, electrical wiring)
- Heat – a source of temperature high enough to start burning
- Oxygen – air that supports combustion
To put out a fire, you must remove at least one element from this triangle.
Fires are classified based on the type of fuel burning. Knowing the class of fire helps you choose the right extinguisher.
| Class | Type of Fire | Common Examples |
|---|---|---|
| Class A | Ordinary combustibles | Wood, paper, cloth, trash |
| Class B | Flammable liquids | Petrol, oil, diesel, grease |
| Class C | Electrical equipment | Wiring, switches, appliances |
| Class D | Combustible metals | Magnesium, aluminum, sodium |
| Class K | Kitchen fires | Cooking oils, fats |
In a solar power installation workshop, Class C (electrical) fires are the most likely to occur.
There are four main methods to extinguish fire. Each method works by removing one element from the fire triangle.
1. Cooling
Pouring water on a fire reduces heat. Water absorbs heat and turns to steam, lowering the temperature below the ignition point.
Example: Using a water extinguisher on Class A fires.
2. Smothering
Covering the fire cuts off the oxygen supply. Without oxygen, the fire cannot continue burning.
Example: Placing a fire blanket over a small fire or using carbon dioxide (CO₂) gas.
3. Starvation
Removing the fuel source removes the material that keeps the fire burning.
Example: Turning off the fuel supply or moving flammable objects away from the fire.
4. Chain Breaking
Using chemical agents to interrupt the chemical reaction of burning. This stops the fire from spreading.
Example: Using dry chemical powder extinguishers.
Different extinguishers work for different classes of fire.
Water Extinguisher
- Color: Red with white label
- Use for: Class A fires only
- Do NOT use: For electrical or liquid fires
Foam Extinguisher
- Color: Red with cream label
- Use for: Class A and B fires
- Do NOT use: For electrical fires
Dry Powder (ABC Powder)
- Color: Red with blue label
- Use for: Class A, B, C, and electrical fires
- Common in: Workshops and vehicles
Carbon Dioxide (CO₂) Extinguisher
- Color: Red with black label
- Use for: Class C and electrical fires
- Advantage: Leaves no residue, safe for electronics
Wet Chemical Extinguisher
- Color: Red with yellow label
- Use for: Class K fires (kitchen)
- Not common in: Solar installation workshops
Follow these four steps when using a fire extinguisher:
- P – Pull the pin to break the tamper seal
- A – Aim the nozzle at the base of the fire
- S – Squeeze the handle to release the extinguishing agent
- S – Sweep the nozzle from side to side at the base of the fire
Worked Example:
A solar panel wire catches fire in the workshop. The correct steps are:
- Alert others and pull the fire alarm
- Identify it as a Class C (electrical) fire
- Use a CO₂ or dry powder extinguisher
- Remember the PASS method: Pull the pin → Aim at the wire → Squeeze handle → Sweep at the base
Never use water on electrical fires because water conducts electricity and can cause shock.
When fighting a fire, always follow these safety rules:
- Ensure you have a clear escape route behind you before approaching a fire
- Stand at a safe distance – usually 2 to 3 meters from the fire
- Never turn your back on a fire
- If the fire is too large or spreading, evacuate immediately
- Call the fire brigade (dial 112 or 110 in Tanzania)
- After extinguishing, watch for re-ignition
- Report all fire incidents to your supervisor
- Stop – Stop what you are doing and stay calm
- Alert – Shout to warn others and activate the fire alarm
- Escape – Leave the area using the nearest exit if the fire is large
- Extinguish – Only attempt to fight small fires if trained and equipped
- Report – Inform the supervisor and complete an accident report
In Tanzania, fire accidents commonly occur at workshops, markets, and homes due to electrical faults or careless handling of flammable materials. For example, if a small fire starts at a solar power installation site in Dar es Salaam, a student who has learned firefighting can use a dry powder extinguisher to control the fire before the fire brigade arrives, potentially saving equipment worth hundreds of thousands of Tanzanian shillings and preventing injuries.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Apply right class of firefighting materials
- Check and test fire extinguishers
Tathmini ya matokeo
Firefighting is performed as standard guideline
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should be able to explain how to perform firefighting
Principles: The students should explain how to perform firefighting
Theories: The students should explain:
- Fire extinguishers
- Responsible authority
Swali
What does the P stand for in the PASS technique used for operating a fire extinguisher?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado