Mada za sehemu hiiInstalling control of DC machinesMada 3
- Installing diverter resistor to the armature
- Installing varistor in the field winding
- Installing autotransformer starter
Autotransformer Starter: Purpose, Working Principle, and Installation
An autotransformer starter is a device used to start DC motors and other electrical machines smoothly by reducing the starting voltage. This reduces the high inrush current that would otherwise damage the motor windings.
The main purposes of an autotransformer starter are:
-
To reduce starting current: When a DC motor starts, it draws a very high current (often 5–7 times the normal running current). The autotransformer reduces the voltage applied to the motor at startup, which limits this high starting current.
-
To protect the motor windings: High starting currents can cause overheating and damage to the motor's armature and field windings. By reducing the voltage, the starter protects these components.
-
To provide smooth starting: The reduced voltage gives the motor a gentle start, reducing mechanical stress on the motor and the connected load.
-
To prevent voltage drop in the supply: Starting a large DC motor without a starter can cause the supply voltage to drop, affecting other equipment connected to the same supply.
The autotransformer starter works on the principle of voltage transformation using a single winding that serves as both primary and secondary.
How it operates:
-
Tapped winding: The autotransformer has a winding with several taps (connections) at different points along the coil. These taps provide different voltage ratios.
-
Initial connection: At startup, the motor is connected to a tap that provides reduced voltage (typically 50%–65% of the full supply voltage).
-
Current path: When the supply voltage is applied, the autotransformer reduces it through the turns ratio. The motor receives lower voltage, so it draws less current.
-
Transition to full voltage: After the motor reaches a certain speed (usually detected by a timer or speed relay), the connection is switched to full supply voltage.
-
Autotransformer disconnected: Once running at full voltage, the autotransformer is disconnected from the circuit, and the motor runs directly from the supply.
Voltage ratio calculation
If the autotransformer has N1 turns on the input side and N2 turns on the output side, the voltage reduction is given by:
VinVout=N1N2
For example, if a transformer has 100 turns input and 60 taps to give 60% voltage: Vout=0.6×Vin=0.6×240V=144V
A typical autotransformer starter wiring diagram includes these main components:
- Autotransformer (AT): The main component with taps at different voltage points
- Motor (M): The DC motor being started
- Start switch: Initiates the starting sequence
- Run switch: Connects the motor to full voltage after startup
- Timer or speed relay: Automatically switches from start to run
- Overload protection: Protects the motor from excessive current
Simple wiring arrangement:
┌─────────────┐
│ AC Supply │
└──────┬──────┘
│
┌──────┴──────┐
│ Fuses │
└──────┬──────┘
│
┌──────┴──────┐
│ Start Switch│
└──────┬──────┘
│
┌──────┴──────┐
│Auto-transformer│
│ (taps 50%, │
│ 65%, 80%) │
└──────┬──────┘
│
┌──────┴──────┐
│ Run Switch │
└──────┬──────┘
│
┌──────┴──────┐
│ DC Motor │
└─────────────┘
Safety first
Before installation, always:
- Wear safety boots, safety goggles, and gloves (leather and plastic)
- Wear overalls for full body protection
- Ensure the work area is clean and free of hazards
- Disconnect power supply before working
Tools and equipment needed
- Set of screwdrivers
- Ball pein hammer and cross pein hammer
- Megger (insulation tester)
- Multimeter
- Diagonal cutting plier
- Combination plier
- Electrician knife
- Rawl plugs for mounting
Installation steps
-
Mount the autotransformer starter on a suitable panel or mounting surface using rawl plugs and screws. Ensure it is securely fixed and accessible for maintenance.
-
Connect the supply wiring from the main power source to the input terminals of the autotransformer starter. Use appropriate cable size for the current rating.
-
Install the motor connections to the output terminals. Ensure correct polarity for DC motor connections (armature and field winding terminals).
-
Wire the control circuit including:
- Start push button
- Run push button or automatic transfer mechanism
- Timer or speed relay connections
-
Set the voltage tap to the desired starting voltage (usually 50% or 65% of full voltage) based on the motor rating and load requirements.
-
Verify all connections are tight and secure. Check for any loose terminals or exposed conductors.
-
Test insulation using the Megger to ensure all circuits are properly insulated before energizing.
-
Check with multimeter that the voltage at the motor terminals is correct before starting.
After installation, practice these checks:
- Use the multimeter to verify voltage at different taps
- Use the insulation tester (Megger) to confirm proper insulation between windings and between windings and earth
- Practice starting and stopping procedures
- Observe the smooth transition from reduced voltage to full voltage
In Tanzania, an autotransformer starter is commonly used in solar power systems that pump water for irrigation in places like Morogoro or Manyara. When starting a DC motor that draws water from a borehole, the reduced starting voltage prevents damage to the motor and avoids causing voltage fluctuations that could affect other appliances in a rural home connected to the same solar system. This reliable starting protects the investment in solar equipment, which can cost over TZS 2,000,000 for a complete pumping system.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Interpret wiring diagrams.
- Install autotransformer starter
- terminate cables
- Test the D.C. machine control.
- Observe safety precautions.
- Clean the work place.
- Store tools, equipment and safety gear.
Tathmini ya matokeo
Autotransfor mer starter is for starting D.C. machines installed as per manufacturer's specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to start DC machine by using autotransformer starter
Principles: The students should be able to explain procedures for Installing autotransformer starter for DC machine
Theories: The students should explain:
- Operation of Autotransformer
- Concept of rectifier circuit
- The importance autotransformer in starting of D.C. machine.
Swali
What is the main purpose of using an autotransformer starter for a DC motor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado