Mada za sehemu hiiPerforming forming operationMada 4
- Performing metal cutting
- Performing metal shearing
- Performing metal bending
- Constructing sheet metal box
Metal shearing is a forming operation that uses sharp blades to cut sheet metal along a straight line without forming chips or burrs. This process is essential for preparing metal sheets to required sizes in electrical installation work, such as cutting conduit trunking and mounting plates.
Metal shearing is a cutting process where a moving blade presses down against a fixed blade to shear or separate the metal along a marked line. The blades apply enough pressure to fracture the metal cleanly. This is different from sawing because shearing produces a straight, clean edge without chips or swarf.
Guillotine Metal Shear
- A machine with a shear-table, ram, holding clamps, gauges, a moving blade, and a fixed blade.
- Used for cutting longer straight lines on sheet metal.
- The metal sheet is clamped and the moving blade descends across the fixed blade to shear the material.
Snip Shear Tool
- Hand tools that look and work like scissors but have sharp blades designed for metal.
- Used for short straight cuts or curved cuts on thin sheet metals.
- Easier to control and suitable for detailed work.
| Metal Type | Maximum Thickness for Snips |
|---|---|
| Steel | 0.7 mm |
| Brass | 0.8 mm |
| Copper | 1.0 mm |
| Aluminium | 1.0 to 2.5 mm |
- Wear appropriate eye protection to protect against flying metal fragments
- Wear gloves to protect hands from sharp edges
- Wear safety boots to protect feet if metal falls
- Wear overalls to protect clothing
- Ensure the workpiece is securely clamped before cutting
- Keep fingers away from the blade path
- Check that the machine is in good working condition before use
Using Snip Shear Tool
- Select the appropriate sheet metal for the task
- Measure and mark out the required dimensions using a steel ruler and scriber
- Use a try square to ensure lines are at right angles where required
- Hold the snips firmly and align the blades with the marked line
- Cut along the marked line using steady, even pressure
- Check the cut dimensions after cutting
- Use a file to remove any burrs or sharp edges on the cut piece
Using Guillotine Metal Shear
- Select the metal sheet to be cut
- Perform marking out according to required dimensions
- Position the metal sheet on the shear-table, aligning the marked line with the blade
- Clamp the metal sheet securely with the holding clamps
- Operate the machine to lower the moving blade across the fixed blade
- Release the clamp and remove the cut piece
- Check measurements and file any burrs
A student is given a sheet of aluminium 1.0 mm thick. The task is to cut a piece 100 mm wide by 150 mm long using snip metal shear.
Steps:
- Measure 100 mm from one edge using a steel ruler and mark with a scriber
- Measure 150 mm from the first mark and mark again
- Use a try square to draw perpendicular lines
- Clamp the sheet if necessary
- Cut along the marked lines using snip shears
- Check that the final piece measures 100 mm × 150 mm
- File any rough edges
In Tanzania, electricians frequently use metal shearing when installing electrical conduit trunking in buildings. For example, when wiring a new classroom in Dodoma, an electrician may need to cut a 1.0 mm thick galvanized steel trunking to size to run wires from the main distribution board to the sockets. Using snip shears, they cut the trunking to the exact length needed, ensuring a neat and professional installation that meets safety standards.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Interpret the drawing.
- Select the material, tools and equipment.
- Mark the workpiece.
- Clamp the workpiece on a vice.
- Mark the start groove with a triangle file.
- Perform metal shearing
- Remove sharp edges with a file.
- Take measurements for accuracy.
- Apply safety measures.
- Clean the workplace, workpieces and tools
Tathmini ya matokeo
Metal shearing is performed as per technical specifications.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to perform metal shearing
Principles: The students should explain principles related to performing metal shearing
Theories: The students should explain:
- Types of metal shearing tools and their functions.
- Main parts of a metal shearing machine.
- The uses of various tools and equipment.
Swali
What is the primary purpose of metal shearing in workshop operations?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado