Mada za sehemu hiiConstructing resistive circuitsMada 4
- Building a single resistor circuit
- Building series resistive circuit
- Building parallel resistive circuit
- Building series – parallel resistive circuit
Series-Parallel Resistive Circuits
A series-parallel resistive circuit (also called a combined circuit) is a circuit that has some resistors connected in series and others connected in parallel within the same circuit. Most real electrical circuits are series-parallel combinations, not purely series or purely parallel. Understanding how to build and analyze these circuits is essential for solar power installation because the wiring in solar panels, batteries, and loads often involves combined connections.
Before building or analyzing a series-parallel circuit, you must identify which resistors are in series and which are in parallel.
Resistors in Series
Two or more resistors are in series when they are connected one after another in a single path. The same current flows through each resistor.
How to identify: If removing one resistor would break the path for current to reach another resistor, those two resistors are in series.
Resistors in Parallel
Two or more resistors are in parallel when they are connected across the same two points. The same voltage is applied across each resistor.
How to identify: If both ends of two resistors are connected to the same two points (forming two common junctions), they are in parallel.
Combined Circuit
A series-parallel circuit contains both types. For example, in the circuit below, resistor R1 is in series with the parallel combination of R2 and R3:
R1
+---[===]---+
| |
| +---[===]---+ (R2 and R3 in parallel)
| | |
+---+---[===]---+
R3
To find the total resistance of a series-parallel circuit, work from the inside out:
- First, simplify the parallel section(s).
- Then, add the series resistances.
Formula for Parallel Resistors
For two resistors in parallel:
Rparallel=R1+R2R1×R2
For three or more resistors in parallel:
Rparallel1=R11+R21+R31
Worked Example
A circuit has three resistors: R1 = 10 Ω in series with a parallel combination of R2 = 20 Ω and R3 = 20 Ω.
Step 1: Calculate the parallel section (R2 || R3)
R23=20+2020×20=40400=10Ω
Step 2: Add the series resistor
Rtotal=R1+R23=10+10=20Ω
The total resistance of the circuit is 20 Ω.
Follow these steps to construct a series-parallel resistive circuit on an electronics board:
- Plan your circuit — Draw the schematic and label all resistors with their values.
- Select resistors — Choose resistors with the correct resistance values. Check values using a multimeter.
- Connect the parallel section first — Place R2 and R3 across the same two rows on the board to create a parallel connection.
- Add the series resistor — Connect R1 in series with the parallel combination using connecting wires.
- Check connections — Verify that all connections are secure and match your circuit diagram.
- Measure with multimeter — Set the multimeter to measure resistance (Ω) and measure across the circuit to verify your calculation.
Safety Notes
- Always wear safety goggles and an overall when working with tools.
- Ensure the soldering iron is placed on its stand when not in use — it becomes very hot.
- Use long nose pliers to handle components and diagonal cutting pliers to trim excess wire.
After finding the total resistance, you can calculate:
- Total current: Itotal=RtotalVsource
- Voltage across series resistor: V1=Itotal×R1
- Voltage across parallel section: This is the same for all parallel branches (they share the same two points).
When the circuit is connected to a power source:
- Use the multimeter in voltage mode (V) to measure voltage across any component.
- Use the multimeter in current mode (A) to measure current through any branch (connect in series).
- Compare your measured values with your calculated values to verify your work.
In a small solar power system for a rural Tanzanian home, the solar panel is connected in series to a charge controller, while multiple LED lights in different rooms are connected in parallel to the controller. If one LED bulb stops working (its filament breaks), the other lights continue working because they are on parallel branches — this is exactly how series-parallel circuits are applied in real solar installations to ensure reliable lighting in the household.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Design a circuit diagram of the series-parallel resistive circuit.
- Select tools, equipment and materials required.
- Prepare resistors and cables for termination.
- Build series-parallel resistive circuit
- Observe safety precautions.
- Clean work area, tools and equipment.
- Store tools, equipment and remaining materials.
Tathmini ya matokeo
The series – parallel resistive circuit is built as per IET regulation.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to build series – parallel resistive circuits.
Principles: The students should explain how to:
- Construct series-parallel resistive circuit circuits.
- Carry out measurements in resistor circuits.
Theories: The students should explain how to:
- Connect series-parallel resistive circuit
- Calculate total resistance
- Calculate current and voltage in the circuit
Swali
What is a series-parallel resistive circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado