Mada za sehemu hiiConstructing inductive circuitsMada 4
- Building a single inductive circuit
- Building a series inductive circuit
- Building a parallel inductive circuit
- Building series parallel inductive circuit
A single inductive circuit is a basic electrical circuit that contains one inductor (also called a coil or choke) connected to a direct current (DC) power source. In this circuit, the inductor stores energy in a magnetic field when current flows through it.
An inductor is a coil of wire usually wound around a core made of iron or air. When electric current passes through the coil, it creates a magnetic field around it. The inductor opposes changes in current flow—a property called inductance, measured in Henry (H).
In DC circuits, inductors allow current to pass steadily after the circuit is closed, but they resist sudden changes in current.
To build a single inductive circuit, you will need:
- A DC power source (such as a battery)
- One inductor (coil with appropriate inductance value)
- Connecting wires
- A switch (optional, for controlling the circuit)
- A multimeter (to measure current and voltage)
Step 1: Plan the Circuit
Draw a simple circuit diagram. A single inductive circuit has the power source, switch, inductor, and connecting wires all in one loop. The components are connected in series—one after another in a single path.
Step 2: Gather Your Tools and Materials
Collect all required tools: electrician knife, combination pliers, diagonal cutting pliers, long nose pliers, multimeter, measuring tape, and safety gear (overalls, safety goggles, and work boots).
Step 3: Prepare the Connecting Wires
Use the electrician knife and pliers to strip the insulation from the ends of the connecting wires. Make sure the exposed copper ends are clean and tight.
Step 4: Connect the Components
- Connect one terminal of the DC power source to one terminal of the inductor using a connecting wire.
- Connect the other terminal of the inductor to the switch (if using one).
- Connect the switch back to the other terminal of the power source, completing the loop.
- Ensure all connections are secure and tight using long nose pliers.
Step 5: Test the Circuit
Close the switch (or complete the circuit) and use the multimeter to measure:
- Voltage across the inductor terminals (set multimeter to DC voltage, V)
- Current flowing through the circuit (set multimeter to DC current, A)
Record your readings.
When you close the circuit:
- Current begins to flow from the power source through the inductor.
- The magnetic field builds up gradually around the inductor.
- Once the magnetic field is fully established, the current reaches its maximum steady value.
- When you open the circuit, the magnetic field collapses and induces a brief voltage spike in the opposite direction.
This behavior is why inductors are used in many electrical devices—to smooth out current changes and protect circuits from sudden surges.
A student builds a single inductive circuit using a 12-volt DC battery and an inductor with inductance of 0.5 Henry. The circuit has a total resistance of 10 ohms.
Calculate the steady current flowing through the circuit.
Using Ohm's Law for the series circuit:
I=RV
Where:
- V=12 volts
- R=10 ohms
I=1012=1.2 amperes
The steady current flowing through the single inductive circuit is 1.2 A.
The student confirms this by setting the multimeter to DC current mode and placing it in series with the circuit.
- Always wear safety goggles and overalls when building circuits.
- Wear safety boots to protect your feet from falling tools.
- Work at a clean workbench, free from clutter.
- Never touch bare copper joints while the circuit is powered.
- Use tools properly—diagonal cutters for cutting wires, long nose pliers for gripping small components.
- Disconnect the power source before making any changes to the circuit.
In Tanzania, a single inductive circuit is the basic principle behind the operation of simple solar charge controllers used in small solar home systems. When connecting a solar panel to a battery, an inductor in the controller helps regulate the current, preventing the battery from overcharging. A farmer in a village near Dodoma might use such a system to charge a 12V battery during the day, powering LED lights in the evening—the inductor in the controller ensures smooth, safe charging of the battery worth approximately TZS 80,000.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Design a circuit diagram of the inductive circuit.
- Select tools, equipment and materials required.
- Prepare inductors and cables for termination.
- Build a single inductor circuit.
- Measure and record the inductive parameters of the circuits.
- Observe safety precautions.
- Clean work area, tools and equipment.
- Store tools, equipment and remainders.
Tathmini ya matokeo
The inductive circuit is built as per IET regulation
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to build a single inductive circuit
Principles: The students should explain how to:
- Construct inductive circuits.
- Carry out measurement in an inductive circuit.
Theories: The students should explain:
- Operation of inductor
- Connection of single inductive circuit
- Calculation of inductive reactance
- Calculation of voltage and current in a single
Swali
What is an inductor?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado