Mada za sehemu hiiConstructing inductive circuitsMada 4
- Building a single inductive circuit
- Building a series inductive circuit
- Building a parallel inductive circuit
- Building series parallel inductive circuit
Building Series-Parallel Inductive Circuits
An inductive circuit is a circuit that contains an inductor (also called a coil or choke). Inductors store energy in a magnetic field when electric current flows through them. When we combine inductors in different ways—series, parallel, or both—we create series-parallel inductive circuits. This topic shows you how to build and analyze these circuits using proper connections and measurements.
When inductors are connected in series, they are connected end-to-end so the same current flows through each one.
Total Inductance in Series
The total inductance (Ltotal) of inductors connected in series is the sum of their individual inductances:
Ltotal=L1+L2+L3+...
Key point: Just like adding resistors in series, inductors in series simply add up.
Example Calculation
If you have three inductors with values:
- L1=10 mH (millihenries)
- L2=20 mH
- L3=30 mH
The total inductance is: Ltotal=10+20+30=60 mH
When inductors are connected in parallel, they are connected across the same two points, so each inductor has the same voltage across it.
Total Inductance in Parallel
The total inductance of parallel inductors is calculated using the reciprocal formula:
Ltotal1=L11+L21+L31+...
Key point: The total inductance of parallel inductors is always less than the smallest individual inductor.
Example Calculation
Two inductors connected in parallel:
- L1=10 mH
- L2=20 mH
Ltotal1=101+201=202+201=203
Ltotal=320≈6.67 mH
A series-parallel inductive circuit combines both series and parallel connections in the same circuit. To analyze or build these circuits:
- Identify the configuration — Look at the circuit diagram and determine which inductors are in series and which are in parallel
- Simplify step by step — First calculate the equivalent inductance of parallel groups, then add the series values
- Build the circuit — Connect the inductors according to the diagram on your electronics board
Steps to Build a Series-Parallel Circuit
- Step 1: Select the inductors required for your circuit
- Step 2: Connect the inductors in the parallel configuration first using your connecting wires
- Step 3: Connect the series inductor(s) to the parallel group
- Step 4: Use the multimeter to verify the connections and measure the total circuit properties
- Step 5: Record your observations and compare with calculated values
When building inductive circuits, always follow safety rules:
- Wear safety goggles and overalls during practical work
- Wear safety boots to protect your feet
- Use proper tools (combination pliers, long nose pliers, diagonal cutting pliers) for connections
- Always disconnect power before making or changing connections
- Keep the workbench clean and organized
Problem: Build a circuit with three inductors: L1=5 mH, L2=10 mH, and L3=15 mH, where L1 and L2 are in parallel, and this combination is in series with L3.
Solution:
-
First, calculate the parallel group (L1 and L2): Lparallel1=51+101=102+101=103 Lparallel=310≈3.33 mH
-
Now add L3 in series: Ltotal=Lparallel+L3=3.33+15=18.33 mH
-
To build:
- Connect L1 and L2 in parallel first
- Then connect one end of L3 to the parallel combination
- Use the multimeter to verify the connections
In Tanzania, series-parallel inductive circuits are found in many electrical systems, including solar power installations. For example, when wiring multiple inductors or chokes in a solar charge controller or inverter, technicians must understand series-parallel configurations to ensure proper current flow and voltage regulation. If a small electronics shop in Arusha needs to replace faulty inductors in a solar system, knowing how to calculate combined inductance helps them select the correct replacement parts and maintain the system's efficiency.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Design a circuit diagram of the inductive circuit.
- Select tools, equipment and materials required.
- Prepare inductors and cables for termination.
- Build a combination circuit.
- Solder the built circuits.
- Measure and record the inductive parameters of the circuits.
- Observe safety precautions.
- Clean work area, tools and equipment.
- Store tools, equipment and remainders.
Tathmini ya matokeo
Series parallel inductive circuit is built as per IET regulation
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to build series parallel inductive circuit
Principles: The students should explain how to:
- Construct series – parallel inductive circuits.
- Carry out measurement in an inductive circuit.
Theories: The students should explain:
- Connection of series-parallel inductive circuit
- Calculation of total inductance
- Calculation of inductive reactance
- Calculation of voltage and current
Swali
What is the total inductance when two inductors of 15 mH and 25 mH are connected in series?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado