Mada za sehemu hiiInstalling switch gearsMada 3
- Installing three phase distribution board
- Installing change over switches
- Installing power factor correction facilities
A three-phase distribution board (DB) is an electrical enclosure that receives power from a three-phase supply and distributes it safely to multiple circuits through protective devices. It organizes protection and control in one unit, ensuring safe and reliable power delivery throughout an electrical installation.
A three-phase distribution board is designed to receive three-phase power and distribute it to multiple circuits within an installation. It houses protective devices such as moulded-case circuit breakers (MCCBs), miniature circuit breakers (MCBs), fuses, and other components—all contained within a single enclosure.
The main components found inside a three-phase distribution board include:
-
Circuit breakers — Devices that automatically interrupt electric current when an excessively high current is detected (from overload or short circuit). They can be reset after tripping.
-
Fuses — Protective devices that melt and break the circuit when excessive current flows. Unlike circuit breakers, fuses are one-time use devices and must be replaced after operating.
-
Busbars — Conductive copper bars that divide and direct incoming power to the circuit breakers in outgoing circuits.
-
Main switch — The primary switching device that disconnects the entire board from the power supply. It is usually an MCCB.
-
Residual Current Devices (RCDs) — Devices that provide protection against electric shock by detecting and interrupting electricity flow when a ground fault occurs (when an energized conductor contacts equipment frame or body).
Three-phase distribution boards are commonly used in commercial and industrial settings where there are higher power demands. Typical applications include:
- Factories with heavy machinery
- Large buildings and commercial complexes
- Facilities requiring reliable power distribution to multiple circuits
Always follow these safety precautions before and during installation:
- Switch OFF the main power supply before starting any work
- Use insulated tools and wear appropriate Personal Protective Equipment (PPE)
- Ensure proper grounding of the distribution board
- Avoid loose connections on terminals
- Adhere strictly to wiring diagrams and manufacturer's instructions
- Keep the installation area dry and clear of obstructions
Follow these step-by-step procedures to install a three-phase distribution board:
Step 1: Preparation
- Wear appropriate PPE (safety boots, overall, safety goggles)
- Study the provided wiring diagram to verify all components
- Gather necessary tools and materials (distribution board enclosure, DIN rails, MCCBs, MCBs, screwdrivers, hammer, measuring tape, spirit level, installation board)
Step 2: Choose Location and Mount Enclosure
- Select an appropriate location that is accessible and safe
- Ensure adequate space for cable entry and exit
- Mount the distribution board enclosure to the wall or installation board using appropriate fixings (rawl plugs, screws)
- Use a spirit level to ensure the enclosure is level
Step 3: Install DIN Rails
- Fix the DIN rails to the internal mounting plate of the enclosure
- Follow manufacturer's instructions
- Ensure rails are level and parallel
Step 4: Mount Protective Devices
- Clip the main switch (MCCB) onto the DIN rail
- Mount individual MCBs and RCDs by clipping them onto the DIN rails
Step 5: Connect Incoming Supply
- Connect the three-phase supply wires (L1, L2, L3) to the main switch (MCCB)
- Connect the neutral wire to the neutral busbar
- Connect the earth wire to the earth busbar
Step 6: Connect Outgoing Circuits
- Connect phase conductors from the MCCB to the final-circuit breakers (MCBs/RCDs)
- Connect corresponding neutral wires to the neutral busbar
- Connect earth wires to the earth busbar
- Ensure all cables are neatly organized and secured
Step 7: Inspection and Testing
- Conduct a final visual inspection to ensure all connections are secure
- Ask your teacher to inspect the installation before powering the circuit
- After approval, test the distribution board and components for correct function
A small workshop in Arusha requires a three-phase distribution board to supply power to three single-phase circuits: a welding machine (32A), a lathe machine (16A), and lighting circuits (10A).
The installation steps would be:
- Install a 63A MCCB as the main switch
- Mount a 32A MCB for the welding circuit on the DIN rail
- Mount a 16A MCB for the lathe circuit
- Mount a 10A MCB for the lighting circuit
- Connect L1, L2, L3 from the main supply to the MCCB
- Connect each phase to its respective MCB
- Connect all neutral conductors to the neutral bar
- Connect all earth conductors to the earth bar
- Label each circuit clearly
During final checks, verify:
- All terminals are tight and secure
- No exposed conductors are visible
- Phase sequence is correct (L1, L2, L3)
- All connections match the wiring diagram
- Labels identify each circuit clearly
- The board is properly grounded
In Tanzania, a three-phase distribution board is commonly installed in small workshops, clinics with medical equipment, and agro-processing businesses like maize mills in towns such as Mbeya or Mwanza. For example, a hardware shop in Dodoma using a three-phase grinding machine would install a distribution board to safely connect the machine alongside lighting and socket circuits, protecting each circuit from overload while ensuring the shop owner can isolate any circuit for maintenance without disrupting power to the entire premises.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to explain how to:
- Interpret wiring diagram.
- Select tools, equipment and safety gear
- Install three phase distribution board
- Observe safety precautions
- Clean the work area.
- Collect all tools and other items for storage.
Tathmini ya matokeo
Three phase distribution board is installed as per IET regulations.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Methods used: The students should explain how to Install three phase distribution board
Principles: The students should be able to demonstrate the correct procedures for installing a three-phase distribution board
Theories: The students should explain:
- Three phase distribution board.
- Protective device available in distribution board
- IET regulation.
Swali
Which of the following components in a three-phase distribution board is responsible for disconnecting the entire board from the power supply?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado