Mada za sehemu hiiDrafting basic traditional blocks patternsMada 4
- Constructing bodice front and back block patterns
- Constructing sleeve block patterns
- Constructing skirt front and back block patterns
- Constructing trousers/shorts front and back block patterns
A trouser block pattern is a basic template created from body measurements that serves as the foundation for drafting different trouser and shorts styles. It ensures a good fit at the waist, hips, and legs while providing enough ease for movement. This study note explains how to construct the front and back block patterns for trousers using standard measurements and drafting techniques.
Measurements Required for Trouser Block Pattern
Before drafting, you need to take accurate body measurements. The key measurements needed are:
- Waist circumference – taken around the narrowest part of the torso
- Hip circumference – taken around the fullest part of the hips
- Waist-to-hip length – measured from the waistline to the hip line
- Body rise – measured from the waistline to the crotch area (where the legs meet)
- Trouser length – measured from the waistline to the floor
- Trouser bottom width – the desired width of the leg at the hem
- Knee width – the desired width of the leg at the knee
These measurements are then converted to working measurements by adding ease (extra space for comfort and movement). The amount of ease depends on the type of fit required – fitted, regular, or loose.
Drafting the Front Block Pattern
Follow these steps carefully to draft the front trouser block:
Step 1: Establish the framework
- Start at point 0 (top left corner)
- Square down and across to create the basic grid
Step 2: Establish key horizontal lines
- Point 1: Body rise + 1 cm – square across (this is the crotch line)
- Point 2: Waist to hip measurement – square across (this is the hip line)
- Point 3: Waist to floor (trouser length) – square across (this is the hem line)
Step 3: Draft the hip and leg width
- Point 4: Half of (1–3) minus 5 cm, square across to mark the knee line
- Point 5: (Hip measurement ÷ 12) + 8 cm, square up to mark points 6 and 7
- Point 8: (Hip measurement ÷ 4) + 1 cm
- Point 9: (Hip measurement ÷ 16) + 1 cm
Step 4: Shape the crotch curve
- Point 10: 1 cm from point 7
- Join 10–6 and 6–9 with a curve, touching 3.5 cm from point 5
Step 5: Complete the waist and leg
- Point 11: (Waist measurement ÷ 4) + 5 cm – this determines waist width
- Point 12: (Trouser bottom width ÷ 2) – 0.5 cm – mark on hem line
- Point 13: Mark on the knee line (point 4 level)
- Join 8–12 and 8–13, then join 13–12 to form the side seam
- Point 14: (Trouser bottom width ÷ 2) – 0.5 cm on the other hem line
- Point 15: Measure equal to 4–13 from point 4
- Join 14–15 and join 9–15, curving inward by 0.75 cm to form the inner leg seam
Drafting the Back Block Pattern
The back block is drafted using the same framework but with different proportions to account for the body's shape.
Step 1: Establish back hip and waist lines
- From point 5, measure (1–5 ÷ 4) to point 16
- Square up to point 17 (hipline) and point 18 (waistline)
Step 2: Shape the back waist
- Point 19: Half of 16–18
- Point 20: 2 cm from point 18
- Point 21: 2 cm from point 20
- Point 22: (Waist measurement ÷ 4) + 6 cm – join to touch the horizontal line from point 0
Step 3: Shape the back crotch curve
- Point 23: (5–9 ÷ 2) + 1 cm from point 9
- Point 24: 0.25 cm from point 23
- Join 21–19, then join 19–24 with a curve touching 4.5 cm from point 16
Step 4: Complete the back leg
- Point 25: (Hip measurement ÷ 4) + 2 cm from point 17
- Points 26 and 27: 1 cm each from points 12 and 13
- Curve 22–25 outward slightly, 25–27 inward slightly, join 27–26
- Points 28 and 29: 1 cm each from points 14 and 15
- Draw the inside leg seam joining 28–29 and 29–24, curving inward by 1 cm
Worked Example
A Tanzanian student named Amina needs to draft a trouser block pattern for a classmate. The measurements taken are:
- Waist: 70 cm
- Hips: 95 cm
- Waist to hip: 18 cm
- Body rise: 24 cm
- Trouser length: 95 cm
- Trouser bottom width: 22 cm
Calculating working measurements:
- Waist with ease: 70 cm + 10 cm = 80 cm (for regular fit)
- Hips with ease: 95 cm + 8 cm = 103 cm (for regular fit)
Drafting calculations (front block):
- 0–1 = 24 + 1 = 25 cm (crotch line)
- 0–2 = 18 cm (hip line)
- 0–3 = 95 cm (hem line)
- 1–4 = (95 – 25) ÷ 2 – 5 = 30 cm (knee line)
- 1–5 = (103 ÷ 12) + 8 = 16.6 cm
- 6–8 = (103 ÷ 4) + 1 = 26.75 cm
- 10–11 = (80 ÷ 4) + 5 = 25 cm
- 3–12 = (22 ÷ 2) – 0.5 = 10.5 cm
These calculated points are then connected following the steps above to create the front and back pattern pieces.
Adding Seam Allowances and Pattern Markings
After completing the block pattern, you must add:
- Seam allowances – typically 1 cm around all edges
- Grainlines – drawn parallel to the centre line of each piece
- Labels – mark "Front" and "Back" on each piece
- Notches – to indicate matching points at waist, hips, and hem
- Dart marks – if required for fitting
Converting Trousers Block to Shorts
To create shorts from the trouser block:
- Measure the desired shorts length from the waistline
- Cut off the pattern at this level
- Add appropriate hem allowance (usually 2–3 cm)
- Re-draw the hemline with a slight curve for a natural appearance
Checking Your Drafted Pattern
Before cutting fabric, always verify your pattern by:
- Checking that front and back pieces have matching hip and waist widths
- Ensuring the inner and outer leg seams meet correctly at the crotch
- Confirming all measurements include proper ease for movement
- Verifying that grainlines are straight and parallel
Real-life application
In Tanzania, tailors in local markets like Kariakoo in Dar es Salaam or Mwenge market use trouser block patterns to create custom-fit trousers for customers. A student who masters this skill could start a small tailoring business, drafting patterns for clients based on their measurements and sewing trousers or shorts for sale. For example, a tailor could charge TZS 25,000–40,000 to draft a pattern and sew a pair of casual trousers, applying this knowledge to earn income while serving community members who need well-fitted clothing.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify block patterns to be made.
- Select tools.
- Take actual body measurements.
- Calculate actual body
- measurements into working measurements.
- Prepare paper for pattern drafting.
- Draw trousers/shorts block patterns on the draft paper.
- Trace drafted block patterns onto hard (Manila) paper.
- Mark and label pattern pieces.
- Cut out pattern pieces.
- Group and pack pattern pieces together.
- Store patterns safely.
- Clean the workplace.
- Store tools.
Tathmini ya matokeo
Construction of trousers/Shorts front and Back block patterns are performed as per technical standard.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Make Trouser/shorts pattern as per
- standard Principles: The student should explain the principles involved in:
- patterns categories
- Caring of patterns drafting tools
- Maintain cleanliness.
- Theories: The student should explain:
- Types of trousers/shorts patterns
- importance of each pattern category
Circumstantial knowledge: Detailed knowledge about:
- Safety procedures while using pattern drafting tools.
- First aid.
- Environmental issues.
Swali
Which of the following measurements is NOT required when drafting a trouser block pattern?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado