Mada za sehemu hiiFatliquoring of leatherMada 3
- Making fat oil
- Applying fat liquor
- Performing conditioning of the pelt
Fat liquor is a mixture of oils, fats, and emulsifiers that is applied to tanned leather to make it soft, flexible, and water-resistant. Without fat liquor, leather becomes hard and brittle after drying.
When leather is tanned, it loses its natural oils. Fat liquor replaces these oils by coating the leather fibers, allowing them to slide past each other rather than sticking together. This gives the leather:
- Softness and flexibility — the leather can bend without cracking
- Strength and durability — fibers are protected from breaking
- Water resistance — the leather repels water better
- Improved texture — the surface feels smoother and more pleasing
Fat liquor is prepared by mixing oils (such as cod oil, castor oil, or neatsfoot oil) with emulsifiers and water. The mixture is heated gently while stirring until it forms a creamy, uniform emulsion.
Common recipe proportions:
- 1 part oil
- 1 part emulsifying agent (such as soap)
- 8 parts water
The mixture is heated to about 50–60°C while stirring continuously until it becomes milky in appearance. This emulsion can then be applied to leather.
Step 1: Prepare the Leather
The leather must be in a wet, tanned state (called "wet blue" or "crust" depending on the tanning method). The leather should be damp but not dripping wet. If it is too wet, the fat liquor will not penetrate properly.
Step 2: Apply the Fat Liquor
The fat liquor can be applied using different methods:
- Brushing — using a soft brush to spread the fat liquor evenly on the leather surface
- Spraying — using a spray bottle or compressed air sprayer for even coverage
- Dipping — immersing the leather briefly in a container of fat liquor (less common for large pieces)
Apply the fat liquor in thin, even layers. It is better to apply two or three thin layers than one thick layer.
Step 3: Allow Penetration
After application, let the leather rest for 15–30 minutes. This allows the fat liquor to soak into the leather fibers. The leather should be kept in a cool, shaded area during this time.
Step 4: Stretch and Set
Gently stretch the leather while it is still damp to open up the fibers and ensure even distribution of the oils. This also helps prevent the leather from shrinking unevenly as it dries.
Step 5: Dry Slowly
Hang the treated leather on a drying board or lay it flat in a well-ventilated area away from direct sunlight or heat. Rapid drying can cause the oils to rise to the surface (called "spewing") and leave greasy spots.
- Wear rubber gloves when handling fat liquor, as some oils can irritate the skin
- Work in a ventilated area, away from open flames (oils are flammable)
- Wear safety boots and an overall coat to protect clothing
- Wash hands thoroughly after handling fat liquor
A small leather workshop in Arusha needs to treat 10 pieces of wet blue leather to make strong shoe soles. Each piece of leather measures 0.5 square meters. They prepare fat liquor using:
- 500 ml of neatsfoot oil
- 500 g of soap (emulsifier)
- 4 liters of water
The workshop heats the mixture to 55°C while stirring until it becomes creamy. They then brush a thin layer of the fat liquor onto each piece of leather, allow it to penetrate for 20 minutes, stretch the leather gently, and hang it to dry in the shade.
After drying, the leather is soft, flexible, and ready for cutting into shoe sole patterns.
In Tanzania, a cobbler in Mwanza or a small-scale leather craftsman in Dar es Salaam would use fat liquor treatment when making leather sandals, belts, or bags. For example, before cutting leather into upper pieces for shoes, the craftsman applies fat liquor to make the leather pliable enough to shape around the shoe last. Without this treatment, the finished shoes would be stiff and uncomfortable, and the leather would crack after only a few weeks of wear.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select material
- Select tools and equipment
- Inspect the pelt for quality
- Wash the pelt
- Treat the pelt
- Prepare pelt
- Estimate amount of water
- Estimate amount of liquid oil
- Estimate quantity of bar soap
- Prepare fat liquor
- Set tanning beams
- Use tanning knife
- Apply fat liquor on the flesh side of leather pelt
- Fold the leather pelt
- Wrap the leather with plastic sheet
- Insert the pelt into wet gunny bag
- Observe fat penetration
- Observe safety
- Clean work place
- Clean tools and equipment
- Store leather and materials
- Store tools and equipment
Tathmini ya matokeo
A pelt is wet with fat oil with good penetration as per required standards.
Tathmini ya maarifa
Detailed knowledge of:
Method used: The student should explain how to:
- Conduct penetration test
- Take precautions in the tan yard
- Scrap leather
Principles: The student should explain the principles of:
- Handling tan yard, chemicals and materials
- Fat liquoring
- Handling tannery tools and equipment
- Using tannery beams
- Applying fat liquoring techniques
Theories: The student should explain:
- Ways of applying fat liquor
- Time required to complete fat liquoring process
- Characteristics of vegetable tanned leather
- Uses of vegetable tanned leather
- Effects of fat liquoring leather
- Importance of precise and detailed work while fat liquoring leather
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions pertaining to fat liquoring
- Safe handling of tanning materials, tools and equipment
- First aid
- Waste disposal
Swali
What is the main purpose of applying fat liquor to tanned leather?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado