Mada za sehemu hiiPerforming leather surface finishingMada 4
- Glazing leather
- Performing measuring of leather
- Performing grading of leather
- Performing packing of leather
Finished leather is sold by its surface area, so every hide or skin that leaves a tannery must be measured and its area recorded. Measuring is done at the end of surface finishing, when the leather is dry, clean and ready for grading and sale. A wrong figure cheats either the tanner or the buyer, so the work must be careful and honest.
- Units of area – Leather area is given in square decimetres (dm2) or in square feet. One square decimetre is a square of 10 cm by 10 cm, so 1 dm2=100 cm2 and 1 m2=100 dm2. One square foot is about 9.3 dm2.
- Irregular shape – A hide or skin is not a rectangle. It has a neck, four legs and curved edges. Multiplying the longest length by the widest width gives an answer that is far too big. The area is found by counting squares or by dividing the shape into simple parts.
- Flat, relaxed and dry – Leather is measured lying flat, smoothed but not stretched, and fully dry. Stretched or damp leather measures bigger than it really is.
- Whole outline – The whole piece is measured, including the belly and legs. Defects are judged afterwards, during grading.
- Characteristics of leather – Leather is a natural material, so no two pieces are the same. The back is thick and firm; the belly and legs are thinner and stretch more. It has a smooth grain side and a rough flesh side, and it takes up moisture from the air.
- Treatment of leather – By the time it is measured, the leather has been tanned, fatliquored (oiled), dried, softened and finished. Handle it with clean hands and do not drag it across the bench: scratches on the grain lower its value.
- Importance of vegetable tanning – Rural tanners use tannins from plants, such as wattle (mimosa) bark. The materials are local and renewable, and no chromium salts are needed. Vegetable-tanned leather is firm, holds its shape, can be moulded and stamped, and suits belts, sandals, saddlery and soles.
- Environmental impact – Tanning uses a lot of water and leaves waste liquors, hair, fleshings and trimmings. Even plant tanning liquors pollute rivers if they are poured away untreated.
| Tool | Purpose |
|---|---|
| Measuring pattern | A frame or clear sheet marked in squares of known size, for example 1 dm² |
| Measuring tape or ruler | Take lengths when a piece is divided into simple shapes |
| Marking pen | Write the area on the flesh side |
| Workbench | Clean, flat surface large enough for the whole piece |
| Leather horses | Hold leather before and after measuring |
| Record book | Keep the area of every piece |
| Safety gloves, safety boots, overcoat or overall, mask | Protect hands, feet, clothes and lungs |
Step 1: Prepare the work area Clear and wipe the workbench and make sure the light is good. Put on your overcoat, safety boots and gloves.
Step 2: Inspect for quality Check that the leather is dry, clean and free from creases, and wipe off dust with a soft dry cloth. Note any holes, cuts or stains for grading.
Step 3: Lay the leather flat Spread the piece on the bench and smooth it from the centre outwards with your palms. Do not pull it.
Step 4: Place the measuring pattern Lay the squared pattern over the leather so that the whole outline is covered.
Step 5: Count the squares Count every square that is completely covered by leather. Then look at the squares along the edge: count a square that is half covered or more as one, and ignore a square that is less than half covered.
Step 6: Work out the area
Area=whole squares+edge squares at least half covered
With 1 dm² squares the answer is in square decimetres. To change it to square feet, divide by 9.3.
Step 7: Check and record Measure a second time; if the two answers differ, measure again. Write the area on the flesh side near the edge with the marking pen, never on the grain. Enter the piece number, type of leather, area and date in the record book.
- Mark out the largest rectangle that fits inside the body of the piece
- Treat the neck, legs and curved edges as small rectangles and triangles
- Measure each part with the tape: the area of a rectangle is length × width, and the area of a triangle is half of base × height
- Add all the areas together to get the total surface area
A tanner in Dodoma measures a finished goat skin with a pattern marked in 1 dm² squares.
- Whole squares covered: 38
- Edge squares half covered or more: 14
- Edge squares less than half covered: 9 (ignored)
- Area: 38+14=52 dm2
- In square feet: 52÷9.3≈5.6 square feet
- A second count gives the same answer, so "52 dm²" is written on the flesh side and in the record book
For comparison, the skin is 95 cm long and 75 cm across at its widest: 95×75=7125 cm2, about 71 dm2, far more than the true area. Length times width must not be used for a whole skin.
- Wear gloves, an overcoat and safety boots; finished leather may still carry dye and finishing chemicals
- Wear a mask if leather is being sanded or buffed nearby, because leather dust harms the lungs
- Lift heavy hides with a partner and keep your back straight
- First aid: wash a small cut with clean water, press it with a clean cloth until the bleeding stops and cover it with a dressing. If dust or a chemical gets in the eye, rinse with plenty of clean water for at least 15 minutes. Report every injury to the person in charge
- Wipe the measuring pattern, tape and bench with a dry cloth, cap the marking pen and return each tool to its place. Hang the pattern or store it flat so that it does not bend
- Store measured leather flat on shelves or loosely rolled, never folded, in a dry, airy store away from direct sunlight and off the floor. Keep pieces of the same type and size together
- Put trimmings and dust in the waste bin and keep useful offcuts for small goods. Do not burn leather waste in the open or throw it into streams; send it to the approved disposal site
- Multiplying length by width for a whole hide or skin
- Stretching the leather, or measuring it while damp
- Measuring only once
- Writing the area on the grain side
- Forgetting to enter the area in the record book
A young tanner near Arusha sells finished goat skins to sandal makers. Because every skin has its area written on the flesh side and in her record book, she can charge a fair price for each square foot and buyers trust her figures. The sandal makers know how many pairs each skin will give, so they buy only what they need and waste less leather.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify tools and equipment
- Inspect for quality
- Take surface measurements
- Observe safety
- Clean leather and materials
- Clean tools and equipment
- Store leather and materials
- Store tools and equipment
Tathmini ya matokeo
Finished leather is measured and recorded its surface area as per required specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Take surface area measurements
Principles: The student should explain the principles related to:
- Leather surface measurements
Theories: The student should explain:
- Characteristics of leather
- Treatment of leather
- Importance of vegetable tanning
- Environmental impact
- Measuring techniques
- Importance of leather surface measurements
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to leather finishing techniques
- Safe handling of tanning materials, tools and equipment
- First Aid
- Waste disposal
Swali
Finished leather is sold by its surface area. Which pair of units is normally used to record the area of a hide or skin?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado