Mada za sehemu hiiPerforming leather surface finishingMada 4
- Glazing leather
- Performing measuring of leather
- Performing grading of leather
- Performing packing of leather
Leather grading is the process of sorting raw or finished leather into different quality levels based on specific characteristics. This helps determine the best use for each piece of leather and ensures fair pricing in the market.
Leather grading is the systematic evaluation and classification of leather according to its quality, appearance, and fitness for purpose. Grading is done after tanning and surface finishing have been completed.
Grading serves three main purposes:
- Quality control — ensures only leather that meets minimum standards reaches customers
- Fair pricing — higher quality leather commands higher prices
- Efficient use — each grade is directed to appropriate products, reducing waste
A grader examines leather for the following characteristics:
- Thickness — measured in millimetres using a leather measuring gauge; uniform thickness scores higher
- Strength — resistance to tearing and stretching
- Surface appearance — absence of scars, brand marks, insect damage, or parasites
- Texture — smoothness and consistency of the grain pattern
- Colour — evenness and richness of the dye
- Flexibility — how easily the leather bends without cracking
- Size — total usable area measured in square decimetres or square feet
Grading systems differ from one tannery or buyer to another, so always ask which system is being used. Two examples are shown below.
Three-Grade System
| Grade | Description |
|---|---|
| Grade 1 (First selection) | Best quality — no defects, uniform thickness, smooth surface |
| Grade 2 (Second selection) | Minor defects such as small scars or uneven colouring |
| Grade 3 (Third selection) | Noticeable defects — used for low-cost products or parts |
Four-Grade System
| Grade | Characteristics |
|---|---|
| A / Super | Clean surface with almost no defects, full and firm leather |
| B / Good | Small surface marks, good structure |
| C / Medium | Visible defects, acceptable for lining leather |
| D / Reject | Heavy damage, suitable only for small parts cut from the sound areas |
Grading also means deciding what each piece is fit for:
- Shoe uppers and fine bags — the best grades: clean grain, even colour and even thickness
- Belts, straps and sandals — thick, firm leather from the back of the hide; small marks can be cut around
- Linings and small goods such as purses and key holders — thinner leather and lower grades, because small parts can be cut from between the defects
- Soles — the thickest, firmest leather; surface marks matter little
The following tools and equipment are needed:
- Workbench — sturdy flat surface for examining leather
- Leather measuring gauge — for measuring thickness
- Measuring patterns — templates to assess usable area
- Marking pen — for labelling graded pieces
- Safety gloves — to protect hands from cuts and chemicals
- Safety boots — foot protection in the workshop
- Overcoat or overall — to protect clothing
Step 1: Prepare the workspace
Set up the workbench in good lighting. Ensure all measuring tools are clean and calibrated. Put on your safety equipment: gloves, boots, and overall.
Step 2: Inspect the surface
Lay the leather flat on the workbench. Examine the entire surface under good light. Look for:
- Scars and cuts
- Brand marks or tick bites
- Parasite holes
- Uneven colouring or dye spots
Mark any defects lightly with chalk that brushes off, or circle them on the flesh side with the marking pen. Never use the marking pen on the grain side: the ink cannot be removed and spoils the leather.
Step 3: Measure thickness
Use the leather measuring gauge to take readings at several points — centre, edges, and corners. Record the thickness in millimetres. Uniform thickness across the piece scores higher.
Step 4: Test flexibility and strength
Fold the leather in several places with the grain side outwards. On good leather the grain does not crack and the wrinkles are fine and close together; coarse, loose wrinkles show a loose grain. Gently pull at the edges to check tear resistance.
Step 5: Measure the usable area
Place the leather on the workbench. Use measuring patterns or a measuring tape to calculate the total usable area in square decimetres. Deduct areas with defects that cannot be used.
Step 6: Assign the grade
Based on your inspection, assign the leather to the appropriate grade. Mark each piece clearly with its grade and area on the flesh side, near the edge, using a marking pen. Record the details in a grading logbook.
A tanner in Morogoro has finished a cowhide after the tanning process. The hide measures 2.5 square metres in total area. Upon inspection:
- Several small tick bites are found on the flank area (about 0.2 m² cannot be used)
- Thickness measures 1.8 mm consistently across the hide
- No scars, colour is even, and the leather bends without cracking
Grade decision: The hide has minor surface defects (tick bites) but good structure and uniform thickness. It qualifies as Grade 2 — suitable for making school bags and belts but not for high-quality shoes that require flawless surfaces.
- Always wear safety gloves when handling freshly tanned leather
- Wear safety boots to protect feet from falling tools or leather pieces
- Use an overcoat to protect your clothes from dye stains
- Work in a well-ventilated area to avoid inhaling any chemical fumes
- Lift heavy hides with a partner, keeping your back straight
- Wipe the measuring gauge and measuring patterns with a clean dry cloth, cap the marking pen and return every tool to its place
- Store graded leather by grade and type, flat on shelves or loosely rolled, never folded, in a dry, airy store away from direct sunlight and off the floor
- Keep the grading logbook with the leather store so that any piece can be traced
- Collect trimmings and rejected scraps in a waste container and keep sound offcuts for small goods. Do not burn leather waste in the open or throw it into streams; send it to the approved disposal site
A leather trader at Kariakoo Market in Dar es Salaam uses grading skills daily when buying hides from rural tanners. By correctly identifying Grade 1 leather, the trader can agree a fair price with the tanner and sell the leather on to shoemakers who need a flawless surface. Conversely, mistaking Grade 3 leather for Grade 2 could lead to losses when the finished product fails quality checks.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify tools and equipment
- Inspect for quality
- Grade the leather
- Take surface measurements
- Observe safety
- Clean tools and equipment
- Store leather and materials
- Store tools and equipment
Tathmini ya matokeo
Pieces of leather are graded according to the required standards
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Differentiate various uses of materials
- Grade leather
Principles: The student should explain the principles related in:
- Quality control
- Leather measurements
- Grading leather
Theories: The student should explain:
- Importance of quality control
- Importance of grading
Circumstantial knowledge:
Detailed knowledge of:
- Waste disposal
Swali
What is leather grading?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado