Mada za sehemu hiiDesigning and making patterns for advanced footwearMada 6
Orthopaedic footwear is specially designed shoes or boots made to support, protect, or correct the shape and function of a foot that has an abnormality, injury, or medical condition. Unlike ordinary shoes, orthopaedic footwear is custom-made or adapted to fit the unique shape and needs of an individual's foot. Making accurate patterns is the first and most important step in producing effective orthopaedic footwear.
Ordinary shoes are mass-produced using standard lasts (foot-shaped forms) and patterns. Orthopaedic footwear, on the other hand, must:
- Accommodate foot deformities such as flat feet, bunions, or missing toes
- Provide extra support where the natural foot structure is weak
- Reduce pain and pressure on sensitive or injured areas
- Allow room for bandages, orthotic inserts, or braces if needed
Because every patient's foot is different, the pattern for orthopaedic footwear must be made by measuring the actual foot or a cast of the foot.
- Extra-depth shoes and boots — deeper and wider than ordinary shoes, with room for a removable insole; for swollen, bandaged or diabetic feet
- Shoes with a raise — a thicker sole and heel on one shoe, for a person whose legs are of unequal length
- Ankle boots with long stiffeners — hold a weak ankle or a foot that rolls inward
- Sandals and shoes with adjustable straps — open wide with Velcro or buckles, for people whose feet swell or who cannot bend easily
Choose fittings and accessories to match the design and the user: Velcro straps or buckles instead of laces for weak hands, padded collars and tongues, soft seam-free linings, and removable insoles.
- A shoemaker does not diagnose or treat a foot disorder. Work from the advice of a doctor or orthopaedic technician, and send anyone with an open wound, numbness or severe pain to a health facility
- Seat the person on a stool, explain what you are going to do, and handle the foot gently and respectfully
- Find out about the problem: ask where the foot hurts, watch the person stand and walk, and look at the wear on their old shoes
- Trace the outline of each foot on paper while the person stands, holding the pencil upright
- Always measure both feet. They are rarely the same, so each foot may need its own last and its own patterns
- Sketch the design, show it to the person, and write the measurements on the sketch before any pattern is made
Before making a pattern, gather the following tools and materials:
- Measuring tape
- Shoe last (adapted to the patient's foot shape)
- Steel ruler
- Soft manila paper
- Tracing paper
- Hard manila paper
- Pencil and eraser
- Cutting knife and cutting block
- Scissors
- Glue and 10 mm gluing brush
- Masking tape
- Footwear catalogue (for reference)
- Hammer and set of hole punches (for marking points)
- Stool for the person being measured
- Plastic boxes for storing sets of patterns
Step 1: Take Accurate Foot Measurements
Use a measuring tape to record the following measurements of the patient's foot:
- Foot length (from heel to the longest toe)
- Foot width (across the widest part of the ball of the foot)
- Ball girth (around the foot at the ball joints)
- Instep circumference (around the top of the foot above the arch)
- Heel circumference
- Height from the floor to the ankle
Record all measurements for both feet, in centimetres, on the sketch and on the foot outline.
Step 2: Select or Adapt the Last
The shoe last is the three-dimensional form around which the shoe is built. For orthopaedic footwear:
- Choose a last that closely matches the overall shape of the patient's foot
- Build up the last with pieces of leather, cork or filler where the foot needs more room, for example over a bunion, a swollen joint or a thick insole
- Check the girths of the adapted last against the foot measurements
- Secure the adapted last firmly on the workbench
Step 3: Cover the Last with Masking Tape
- Cover the whole upper surface of the last with strips of masking tape, each strip overlapping the one before
- Add a second layer running the other way so that the tape shell is strong
- Rub the tape down firmly so there are no wrinkles or air pockets, especially around the toe and heel
Step 4: Mark the Seam Lines and Key Reference Points
While the tape is on the last, use a pencil to draw the design from your sketch on it. Mark the following:
- Centre line down the front of the last (from the toe to the top of the instep) and down the back of the heel
- Seam lines for the upper (vamp and quarter)
- Edge line where the upper meets the sole
- Any openings, straps, or special features required
Step 5: Remove and Flatten the Pattern
- Cut through the tape along the front and back centre lines with the cutting knife
- Peel off the inside and outside halves carefully
- Stick each half flat on soft manila, making small cuts at the toe and heel curves so that the tape lies flat without wrinkles
- Cut round the outline. This flat shape of the last is the master pattern
Step 6: Trace and Refine the Pattern
- Place the master pattern on the workbench and lay tracing paper over it
- Trace each part of the upper separately (vamp, quarters, tongue, stiffener and linings) with its seam lines and reference marks
- Add the correct allowance to each edge: about 15–20 mm on the bottom edge for lasting, about 8–10 mm where one part lies under another, and about 4–5 mm on an edge that will be folded
- Label each pattern piece clearly with the order name or number, the part (for example vamp or outside quarter), left or right foot, and the size
Step 7: Transfer to Hard Manila and Cut Out
- Place the traced pattern on hard manila paper
- Secure it with masking tape to prevent slipping
- Cut out each pattern piece carefully using scissors or a cutting knife on a cutting block
- Punch small holes at all marked reference points (marking points) for easy alignment during assembly, using a hole punch and hammer on the cutting block
Step 8: Grade, Check and Arrange the Patterns
- Grading means making the same pattern larger or smaller for other sizes. Most orthopaedic footwear is made for one person, so instead of grading a full range of sizes the patterns are adjusted for that person's left and right feet
- If a design is to be made in several sizes, grade the patterns one size at a time, keeping the same proportions
- Check that the parts fit together along their seam lines and that every piece is labelled
- Tie or clip all the pieces for one shoe into a set, and keep the left and right sets together
Scenario: A patient has a flat left foot: the arch has collapsed and the foot rolls inward. The following measurements were taken:
- Foot length: 26 cm
- Ball width: 10 cm
- Instep circumference: 24 cm
Pattern-making process:
- A last close to the size of the foot is selected and built up over the instep to make room for an arch-support insole
- The adapted last is covered with two layers of masking tape
- The centre lines, the seam lines and the line of a long inside stiffener are marked on the tape
- The tape is cut along the centre lines, peeled off and flattened on soft manila
- Each part is traced, with 18 mm added for lasting, 8 mm for underlays and 4 mm for folded edges
- The parts are transferred onto hard manila, labelled (for example "Left vamp, flat-foot order") and cut out
The resulting patterns give an upper with room for the arch-support insole and a long, firm stiffener on the inside that helps to hold the heel steady. The support itself comes from the insole, which is made as the health worker advises.
- Always measure the patient's actual foot before selecting or modifying the last
- The last must reflect every unique feature of the patient's foot
- Use the correct allowance for each edge: lasting, underlay and folding allowances are different
- Work precisely: an error of a few millimetres can cause pressure and sores on a foot that is already damaged
- Label every pattern piece clearly to avoid confusion during cutting and assembly
- Wear a dust coat, and cut only on the cutting block with a sharp knife
- Flat foot — collapsed arch requiring built-in arch support
- Bunions — enlarged joint at the base of the big toe, requiring a wider toe box
- Club foot — twisted foot requiring a specially shaped last and pattern
- Diabetic foot — a foot that may have lost feeling and heals slowly, so that small rubs can become serious wounds; it requires soft, seam-free linings and extra depth
- Cut on a cutting block with a sharp knife, guiding it along the steel ruler and keeping the fingers of the holding hand behind the blade
- Cover the blade when the knife is not in use, and pass scissors handle first
- Use glue in a well-ventilated place, keep the container closed and keep it away from flames
- For a cut, wash the wound with clean water, press with a clean cloth until the bleeding stops and cover it with a dressing. Report every injury
- Brush dust and dried glue off the patterns, keep them flat and dry, and store each set in a labelled plastic box or hang it on a hook through a punched hole
- Clean the gluing brush, wipe the knife, ruler and last, and return all tools to their places
- Put offcuts of manila and tape in the waste bin
In Tanzania, many people — especially farmers, market vendors, and construction workers in places like Arusha, Mwanza, and Dar es Salaam — suffer from foot problems caused by long hours of walking on hard surfaces, poorly fitting shoes, or diabetes. A local shoemaker who knows how to make orthopaedic footwear patterns can serve their community by crafting affordable custom shoes that relieve pain and prevent further injury, earning an income while helping neighbours walk comfortably again.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify different orthopedic footwear designs
- Identify materials
- Select tools and equipment
- Identify end users
- Create original style and sketch preliminary designs
- Determine matching fittings and accessories
- Take measurements
- Interpret measurements into sketches
- Develop master patterns
- Trace master patterns
- Transfer master pattern into hard manilla
- Develop various parts of master patterns
- Cut patterns from hard manilla
- Grade patterns
- Label patterns
- Insert marking points
- Arrange patterns into sets
- Observe safety
- Clean pattern
- Clean tools and equipment
- Store patterns
- Store tools and equipment
Tathmini ya matokeo
Patterns for orthopedic footwear designs conform to required product specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Identify materials
- Take measurements
- Trace different designs and styles
- Trace standard sizes
- Transform sketches
- Produce master patterns
- Grade patterns
Principles: The student should explain the principles of:
- Attend a person who require orthopedic footwear
- Making sketches
- Taking foot measurements
Theories: The student should explain:
- Types of footwear designs
- The research techniques for foot disorders
- Importance of precise and detailed work while making patterns for orthopaedic footwears
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to pattern cutting
- Safe handling of designs and patterns
- First aid
- Waste disposal
Swali
The first step in making patterns for orthopaedic footwear is to …
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado