Mada za sehemu hiiDesigning and making patterns for advanced footwearMada 6
A football shoe pattern is a template or blueprint that outlines the exact shape and size of each piece of leather or material needed to construct a complete football boot. Making accurate patterns is the foundation of producing well-fitted, comfortable, and durable football shoes.
Before you start cutting and drawing, you must understand these key principles:
- Proper measurement — Take accurate measurements of the foot using a measuring tape. Length and width are essential.
- Allowances — Add the correct extra margin to each edge: about 15–20 mm on the bottom edge for lasting, about 8–10 mm where one part lies under another, and about 4–5 mm on an edge that will be folded.
- Symmetry — The left and right shoe parts should mirror each other.
- Consider the last shape — The pattern must follow the curvature of the shoe last (the foot-shaped mould used in shoe making).
- Functionality — Football shoe patterns must include specific features such as stud positions on the sole, a firm heel stiffener, and a reinforced toe and vamp for kicking.
A derby is an everyday laced shoe in which the quarters are stitched on top of the vamp, so that the lacing opens wide. Many football shoes are cut in a similar way, but they are designed for running and kicking.
| Feature | Derby shoe | Football shoe |
|---|---|---|
| Use | Everyday and office wear | Playing football on a pitch |
| Fit | Comfortable, with some room | Close and snug, so that the foot does not slide |
| Upper | Firm leather that keeps a smart shape | Thin, soft, strong leather or synthetic material, often with rows of stitching on the vamp for strength |
| Lacing | Short, over the instep | Longer, reaching further towards the toes |
| Toe | Shaped, with a firm toe puff | Low and close to the foot, to feel the ball |
| Bottom | Flat sole with a separate heel | Firm sole with studs and no raised heel |
- Study designs in a footwear catalogue: shoes with moulded studs for firm ground, shoes with longer screw-in studs for soft ground, and flat-soled shoes for hard or indoor pitches
- Sketch your own style from the side and from above, showing the panels, the lacing and the stud positions
- Choose colours and trims that match the team's kit: the shirt, shorts and socks
- Write the measurements on the sketch so that it can be turned into a pattern
| Tool/Material | Purpose |
|---|---|
| Shoe last | Model for shaping the pattern |
| Measuring tape | Measuring foot dimensions |
| Steel ruler | Drawing straight lines |
| Soft manila paper | Making initial pattern drafts |
| Hard manila paper | Making final durable patterns |
| Tracing paper | Transferring pattern outlines |
| Pencil and eraser | Sketching and correcting |
| Cutting knife and scissors | Cutting out pattern pieces |
| Cutting block | Protecting surfaces during cutting |
| Masking tape and gluing brush | Covering the last to lift off its shape; sticking pattern parts down |
| Hammer and set of hole punches | Making marking points and holes for hanging patterns |
| Footwear catalogue | Reference for design styles |
Step 1: Taking Foot Measurements
Measure the client's foot carefully using a measuring tape. Record:
- Foot length (in centimetres)
- Foot width at the widest point
- Ankle circumference
- Ball girth and instep girth (measured around the foot)
These measurements will guide the pattern dimensions.
Step 2: Selecting the Shoe Last
Choose a shoe last that matches the foot measurements taken. The last determines the overall shape and fit of the football shoe.
Step 3: Drafting the Upper Pattern
The upper (the top part of the shoe) consists of several panels:
- Toe cap — Front piece covering the toes
- Vamp — Middle section connecting the toe to the instep
- Quarters — Side and heel panels
- Tongue — Central strip under the laces
- Lining pieces — Inner surface patterns
To get the shape of the last, cover it with two layers of masking tape, draw the centre lines and the panel lines of your design on the tape, cut along the centre lines, peel the tape off and stick it flat on soft manila. This flat shape is the master pattern. Trace each panel from it onto soft manila, adding the correct allowance to each edge.
Step 4: Drafting the Sole Pattern
The sole pattern includes:
- Insole — Inner sole matching the foot shape
- Outsole — Outer sole with stud positions marked
- Midsole — A thin middle layer, if the design has one; many football shoes have none, so that the foot stays close to the ground
Draw the insole pattern round the bottom of the last.
Step 5: Refining and Labelling
- Check all pieces for accuracy
- Label each pattern piece clearly (e.g., "Left Toe Cap," "Right Quarter")
- Show with an arrow the direction in which the leather must not stretch (uppers are cut tight from toe to heel)
- Mark notches and punch small holes (marking points) to show where parts overlap and where eyelets and stitch lines go
Step 6: Transferring to Hard Manila
Once the soft manila draft has been checked, trace it onto hard manila paper for durability. Cut out the final pattern pieces with a sharp knife on the cutting block.
Step 7: Grading and Arranging into Sets
- Grading means making the same pattern in larger and smaller sizes. In the English size system each full size is about 8.5 mm longer than the one before; in the European (Paris point) system each size is about 6.7 mm longer. The width grows in proportion
- Grade from the checked middle size, one size at a time, and label every piece with its size
- Punch a hole in each piece and hang or tie all the pieces of one size together as a set
A Form 3 student measures a foot with the following dimensions:
- Length = 26 cm
- Width = 10 cm
Using these measurements on a matching last, the student:
- Covers the last with masking tape, draws the design on it, and flattens the tape on soft manila to get the master pattern
- Traces the toe cap, adding 18 mm on the bottom edge for lasting and 4 mm on the back edge, which will be folded
- Traces the vamp, adding 8 mm at the front where it lies under the toe cap and 18 mm on the bottom edge
- Traces the two quarters (inside and outside), adding 18 mm on the bottom edge
- Cuts and labels all pieces
- Verifies that the pieces fit together properly along their seam lines
- Always use a cutting block when cutting pattern pieces
- Wear safety gloves when handling cutting tools
- Use scissors and knives carefully, cutting away from your body
- Keep the fingers of the holding hand behind the blade and guide the knife along the steel ruler
- Strike hole punches on the cutting block, not on the bare workbench, and keep your fingers clear of the hammer
- Keep your workbench clean and organised
- Brush dust and bits of tape off the patterns and keep them flat and dry
- Store each set in a labelled plastic box or hang it on a hook
- Wipe the knife, ruler and last, clean the gluing brush, and return all tools to their places
- Put offcuts of manila and tape in the waste bin
A young Tanzanian cobbler in Arusha who masters football shoe pattern making can start a small workshop producing affordable football boots for local football clubs and school teams. With a set of graded patterns he can cut any size quickly and accurately, which gives him a steady income while serving the growing demand for sports footwear in his community.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Identify the designs
- Identify materials
- Select tools and equipment
- Create original style and sketch preliminary designs
- Determine matching dresses
- Take measurements
- Interpret measurements into sketches
- Develop master patterns
- Trace master patterns
- Transfer master pattern into hard manilla
- Develop various parts of master patterns
- Cut patterns from hard manilla
- Grade patterns
- Label patterns
- Insert marking points
- Arrange patterns into sets
- Observe safety
- Clean pattern
- Clean tools and equipment
- Store patterns
- Store tools and equipment
Tathmini ya matokeo
Patterns for football shoe designs conform to required product specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Making pattern for football shoe
Principles: The student should explain the principles related in:
- Making pattern for football shoes
Theories: The student should explain:
- The differences between football and derby shoes
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions pertaining to pattern cutting
Swali
What is the correct allowance added to the bottom edge of a football shoe pattern piece for lasting?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado