Mada za sehemu hiiSupervising corrective and preventive maintenanceMada 2
- Performing preventive maintenance of machines and equipment
- Performing corrective maintenance of workshop machines
Corrective maintenance is the type of maintenance that is carried out after a machine has broken down or is not functioning properly. Its purpose is to restore the machine to its normal working condition by repairing or replacing faulty parts.
It is important to understand the difference between these two types of maintenance:
- Corrective maintenance is done after a problem occurs — you react to a fault or breakdown.
- Preventive maintenance is done before problems occur — you service machines regularly to stop faults from happening.
Before performing corrective maintenance, gather the following:
Hand tools:
- Screwdrivers (flat and Phillips)
- Spanners and wrenches
- Pliers
- Hammer
- Adjustable wrench
Workshop equipment:
- Lubricating oil and grease
- Cleaning rags
- Service manuals for the machines
- Replacement parts if needed
Personal protective equipment (PPE):
- Gloves
- Safety boots
- Safety glasses or goggles
- Overcoat, overall, or apron
- Dust mask
Always wear your PPE before starting any maintenance work to protect yourself from injuries, oil, dust, and moving parts.
Follow these steps carefully when carrying out corrective maintenance on workshop machines:
Step 1: Identify the Problem
Observe the machine and listen to it. Look for signs such as strange noises, vibrations, overheating, or irregular movement. Refer to the machine's service manual to help diagnose the fault.
Step 2: Isolate the Machine
Switch off the machine and disconnect it from the power supply. This prevents the machine from accidentally starting while you are working on it. Wait until all moving parts have stopped, and hang a sign on the machine saying "Under repair – do not use" so that nobody reconnects it.
Step 3: Disassemble the Faulty Part
Remove covers, guards, or components to access the damaged part. Use the appropriate tools and follow the steps described in the service manual. Keep screws and small parts in a safe place so they are not lost.
Step 4: Inspect and Diagnose
Examine the faulty component closely. Check for wear, cracks, loose connections, or missing parts. Determine whether the part can be repaired or must be replaced.
Step 5: Repair or Replace the Faulty Part
- If repairable, fix the component using appropriate tools and techniques.
- If not repairable, remove the old part and install a suitable replacement.
- If the fault is electrical (motor, switch, plug or wiring), do not open or repair it yourself. Report it so that a qualified electrician can do the work.
Step 6: Reassemble the Machine
Put all components, covers and guards back in their correct positions. Tighten screws and bolts firmly but do not overtighten them, as this can damage the machine.
Step 7: Lubricate Moving Parts
Apply lubricating oil or grease to all moving parts as specified in the service manual. Proper lubrication reduces friction and prevents premature wear.
Step 8: Test the Machine
Check that all guards are fitted and that no tools or rags are left on the machine. Keep hands, gloves and loose clothing clear of moving parts, then reconnect the power supply and switch on the machine. Observe its operation to confirm that the fault has been corrected and the machine runs smoothly.
Step 9: Record the Maintenance Work
Write a maintenance report documenting:
- The machine serviced
- The problem identified
- The repair or replacement made
- Parts used
- Date and name of the technician
- Before any repair, check that the plug is out of the socket; switching off at the machine is not enough
- Work with dry hands on a dry floor, and never use a machine with a damaged cable, a cracked plug or a missing earth connection
- Leave all repairs to motors, switches and wiring to a qualified electrician
- Heavy machine heads, motors and stands are lifted by two or more people: stand close, bend the knees, keep the back straight, and agree who gives the signal to lift
- Support a machine head properly before working under it, and clear the floor before moving heavy items
Safety signs follow a colour code: red for stop or "do not", yellow for a warning, blue for something you must do or wear, and green for safe things such as first aid. During a repair, the red "do not use" sign stays on the machine until the test is passed.
Good environmental practice is part of the job:
- Collect used oil and grease in a labelled container for proper disposal; never pour it on the ground or into a drain
- Put oily rags in a closed metal bin, and broken needles, blades and sharp metal parts in a strong closed tin
- Hand in worn metal parts and old belts for scrap or safe disposal
- Wipe every tool clean, check that none is missing, and return the tools and the service manual to their places
Because repairs can be dangerous, corrective maintenance should be planned and taught. People who have been shown the correct method on each machine repair it faster, damage fewer parts and are less likely to be hurt.
A sewing machine in the workshop suddenly stops working during a practical lesson. The technician follows these steps:
- Identifies the problem — the motor runs when the pedal is pressed, but the handwheel and needle do not move.
- Isolates the machine — switches off and unplugs the machine.
- Disassembles the faulty part — removes the belt guard to reach the drive belt.
- Inspects and diagnoses — finds that the drive belt has snapped.
- Replaces the faulty part — fits a new drive belt of the correct size.
- Reassembles the machine — refits the belt guard and tightens the screws.
- Lubricates moving parts — applies oil to the needle bar and other joints.
- Tests the machine — plugs in and runs the machine; it operates normally.
- Records the work — writes a report: "Drive belt replaced on sewing machine No. 3, 14 May."
After completing the practical work, organise into groups and present your maintenance reports. Each group should:
- Describe the machine they serviced
- Explain the fault they found
- Outline the steps they followed
- Share what they learned from the activity
- Always disconnect power before starting maintenance.
- Wear your PPE at all times.
- Use the correct tools for each task.
- Follow the service manual for your specific machine.
- Never rush — take time to diagnose the problem correctly.
- Always document your work in a maintenance report.
In Tanzania, many small tailors and cobblers rely on sewing machines and leather-working equipment to earn a living. If a machine breaks down during a busy market day in Kariakoo or Arusha, a person who knows corrective maintenance can quickly diagnose the fault, replace a worn part like a drive belt or needle, and get the machine running again — saving the cost of calling an outside technician and avoiding lost income. This skill also helps in family-owned workshop businesses where machines are a major investment worth protecting through proper repair and record-keeping.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Interpret service manuals
- Read and apply rules and regulations
- Prepare and apply workshop inspection report
- Prepare and use safety signs and color code
- Practice corrects heavy tools/equipment safely
- Practice good electrical safety
- Monitor good and environmental practices
- Clean tools and equipment
- Store tools and equipment accordingly
Tathmini ya matokeo
Corrective maintenance of workshop machines is performed as per workshop standards
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Perform corrective maintenance of workshop machines
Principles: The student should explain the principles related to:
- Perform Corrective maintenance of workshop machines
Theories: The student should explain:
- Importance of planning and conducting corrective maintenance training
- Importance of follow good environmental practices
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions while conducting corrective maintenance
- Safe handling of tools and equipment
- Waste disposal
Swali
What is corrective maintenance?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado