Mada za sehemu hiiMaking stitchesMada 4
- Making temporary stitches
- Making joined stitches
- Making fancy stitches
- Performing stitching by hand
Temporary stitches are short, loose stitches used to hold leather pieces together before permanent stitching. They are removed easily once the final stitches are in place, allowing you to adjust or correct mistakes during the making of leather goods and footwear.
Temporary stitches, also called tacking stitches or basting stitches, are preliminary stitches made to hold two or more pieces of leather in position temporarily. They serve as a guide before the actual permanent stitching or gluing is done.
- To hold leather pieces together while you check the fit and alignment
- To prevent leather pieces from shifting while the permanent stitching is done
- To allow easy removal and adjustment if mistakes are noticed
- To hold linings, zips and other parts exactly where the pattern shows
- Temporary stitches are long, loose stitches that hold pieces in place for a short time. They are taken out when the permanent work is finished.
- Joining stitches are the permanent stitches that hold the product together, such as the saddle stitch and the back stitch. They are short, tight and evenly spaced.
- Decorative stitches are sewn to make the product look attractive, such as a cross stitch or a row of stitching in a contrasting colour.
The usual temporary stitch is a long running stitch, called tacking. Leather differs from fabric in one important way: a needle hole in leather never closes. For this reason, temporary stitches in leather are placed inside the seam allowance, where the holes will be hidden, or in holes that the permanent stitches will later use.
- Needle: for thin, soft leather use a leather (glover's) needle, which has a sharp three-sided point that cuts its own way through. For thicker leather, make the holes first with an awl and use a blunt harness needle. For fabric linings use an ordinary sharp sewing needle.
- Thread: a thin, smooth thread in a colour that stands out from the leather is best for tacking, because it is easy to see and easy to pull out.
- Matching needle and thread: the thread must pass easily through the eye of the needle, and the needle must make a hole just big enough for the thread. A thick needle with a thin thread leaves large, ugly holes; a thin needle with a thick thread is hard to pull through and may break.
- Single or double thread: a single thread, knotted at one end only, is usual for tacking. Use a double thread, with both ends knotted together, only where the pieces are heavy and need a firmer hold.
Before you start, study the working drawing or pattern. It shows which pieces are joined, where the seam line runs and how wide the seam allowance is, so you know where the temporary stitches may go.
- Sharp scissors
- Measuring tape or ruler
- Marking pencil or chalk
- Leather (glover's) needle or harness needle
- Awl (for making holes in thicker leather)
- Thin thread in a colour that shows clearly against the leather
- Thimble (optional, to protect fingers)
Safety Gear
- Safety gloves to protect hands from needle pricks
- Safety boots to protect feet in the workshop
- Dust coat or overalls to protect clothing
Step 1: Prepare the Leather Pieces
Lay the leather pieces on a flat workbench. Ensure they are clean and free from dust. Align the edges you want to join and check that they fit properly.
Step 2: Mark the Stitching Line
Using a ruler and marking pencil, draw a light line where you want the stitches to go, inside the seam allowance or exactly on the line of the permanent stitching. Mark small dots at equal intervals, typically 1–2 centimetres apart, to show where each stitch will pass through.
Step 3: Thread the Needle
Cut a length of thread about 60 centimetres long. Thread it through the needle and tie a small knot at the end. The knot should be large enough that it cannot pull through the hole.
Step 4: Start Stitching
On thicker leather, first make a small hole at each marked point with an awl. Then insert the needle from the back of the leather to the front at the first marked point. Pull the thread through until the knot rests against the back of the leather.
Step 5: Make the Stitches
Insert the needle at the next marked point, bringing it through to the back. Then insert it again at the third point, bringing it back to the front. Continue this in-and-out pattern, creating a line of long, loose running stitches.
Step 6: Secure the Stitches
When you reach the end, do not tie a knot. Make one small stitch back over the last stitch, or leave a tail of thread about 3 centimetres long, so that the thread can be pulled out later. Do not make the stitches too tight — they should be loose enough to be pulled out easily later.
Step 7: Check the Alignment
Gently pull the leather pieces to check that they are held firmly together. If any area is loose or misaligned, you can adjust it by loosening those specific stitches and repositioning.
Suppose you are making a simple leather belt and need to join two straps end to end with an overlap. You place the straps on the workbench with the end of one lying about 4 cm over the end of the other. You mark stitch points at 1.5 cm intervals along the line where the permanent stitches will go. Starting from the back, you insert the needle at the first mark, bring it to the front, then insert at the second mark and bring it to the back. You repeat this, keeping the stitches loose. After completing the tacking, you check that the straps are straight and aligned. If they are not straight, you pull out the stitches, adjust the straps, and stitch again.
Temporary stitches inside the seam allowance are removed when the permanent stitching has been completed and checked. Temporary stitches on the line of the permanent stitching are removed a few at a time, just ahead of the permanent stitches. Cut off the starting knot with scissors, then pull the thread out gently from the other end. On a long seam, snip the thread every few stitches and pull out the short pieces, taking care not to cut the permanent stitches or the leather. Remove every piece of tacking thread before the product is finished.
- Always wear safety gloves when handling needles and sharp tools
- Keep the workbench clean and free from loose thread scraps
- Sit properly on the workshop stool to maintain good posture
- Use safety boots in case any tools fall
- Never hold needles in your mouth or stick them into your clothes; keep them in a needle case and count them before and after work
- Pass scissors to another person handle first, and keep the point of the awl covered when it is not in use
A needle prick or a small cut is the most likely injury. Stop work, wash the wound with clean water and soap, press on it with a clean cloth until the bleeding stops, and cover it with a clean dressing. Report every injury to the person in charge of the workshop. A deep cut, or a broken needle point left in the skin, needs attention at a health facility.
- Collect thread ends and leather scraps and put them in the dustbin
- Put bent or broken needles in a closed tin or box before they are thrown away, so that nobody is pricked
- Wipe the scissors, awl and ruler with a dry cloth, then wipe the workbench and sweep the floor
- Store needles in their case, thread on its reel and all tools in their proper places, in a dry cupboard so that they do not rust
- Temporary stitches are loose and easy to remove
- Always mark stitch points before stitching to ensure even spacing
- Check alignment after stitching before proceeding with permanent work
- Place temporary stitches where their holes will be hidden or used again, and remove them once the permanent stitching is done
In Tanzania, temporary stitching is commonly used by leather craftspeople (mafundi) in local workshops, such as those found around the markets of Dar es Salaam or Zanzibar. A craftsperson fitting a fabric lining or a zip into a leather bag will first use temporary stitches to hold it in place, check the fit, and make adjustments before sewing the permanent stitches. This skill saves time and materials because mistakes can be corrected before the work becomes permanent.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select materials
- Select tools and equipment
- Interpret working drawing or patterns
- Select type of stitches
- Select correct types of needles.
- Select thread to suit the type of leather and fabrics and needle sizes
- Construct stitches using single or double thread
- Work temporarily to joining stitches with required precision
- Observe safety precautions
- Clean workplace
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
Temporary stitches are formed according to the specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should clearly explain how to:
- Select different types of needles, stitches, threads suitable for different types of leathers
- Procedures of making different types of stitches
Principles: The student should clearly explain the principles of:
- Handling stitching
- Adjusting stitch lengths
Theories: The student should explain:
- The differences between temporary, joining and decorative stitches
- The relationship between threads and needles
- Relationship between materials, needles and threads
- The importance of precise and detailed work while making stitches
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions on to sewing operation
- Safe handling of tools and equipment
- First aid
- Waste disposal
Swali
Temporary stitches are also known as tacking stitches or basting stitches. What is their main purpose?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado