Mada za sehemu hiiMaking stitchesMada 4
- Making temporary stitches
- Making joined stitches
- Making fancy stitches
- Performing stitching by hand
Joined stitches, also called joining stitches, are the permanent stitches that hold two or more pieces of leather or fabric together in a finished product. They are short, tight and evenly spaced, so that they make a neat and strong seam.
Joined stitches are made by passing the needle and thread through a row of evenly spaced holes so that the thread binds the pieces firmly together. Stitches fall into three groups:
- Temporary stitches are long, loose stitches that only hold pieces in place while you work, and are pulled out afterwards.
- Decorative stitches are sewn mainly to make the product look attractive.
- Joined stitches carry the strain when the product is used, so they must stay in place for the whole life of the product.
Key characteristics
- They are permanent and are not removed
- Every stitch is the same length and lies the same distance from the edge
- Creates a neat, uniform appearance on both sides of the leather
- Provides strong holding power for leather seams
At Form 1 level, we learn the following basic joined stitches:
-
Running stitch – The needle goes in and out, in and out, along the stitch line, so that stitches and gaps alternate on each side. Simple and quick to learn, but the weakest of the three.
-
Saddle stitch – One thread carries a needle at each end, and both needles pass through every hole from opposite sides, so the threads cross inside the leather. This is the strongest joined stitch.
-
Back stitch – Each new stitch begins by going back to where the previous stitch ended, creating a solid line.
Start with the working drawing or pattern. It shows which pieces are joined, where the stitch line runs, how far it is from the edge and how long the stitches should be. Then choose:
- The stitch: saddle stitch for seams that carry strain, such as straps and handles; back stitch where you work with one needle and still need a strong seam; running stitch for light work and linings.
- The thread: thick, firm leather needs a thick, strong thread; thin leather and fabric need a finer one. Waxed thread grips the leather and resists water and rubbing.
- The needle: the eye must be just big enough for the thread, and the needle should be no thicker than the hole needs to be. A needle that is too thick leaves large holes; one that is too thin is hard to pull through and can snap.
- Single or double thread: a single thread is knotted at one end and gives a fine, flat stitch. A double thread, with the two ends knotted together, gives a thicker, stronger stitch for heavy leather.
Stitch length must also suit the material: about 3 to 4 mm for thin leather and fabric, and 5 to 6 mm for thick leather. Stitches that are too short put the holes so close together that the leather can tear along the line; stitches that are too long leave gaps and a weak seam. By hand, the stitch length is set by how far apart you mark the holes. On a sewing machine it is set with the stitch-length regulator.
Materials needed
- Leather pieces to join
- Waxed linen, polyester or nylon thread
- Blunt harness needles (for holes made in advance) or a sharp leather needle (for thin, soft leather)
- Awl or pricking iron
- Thimble
- Stitching pony or clamps
- Scissors, ruler and measuring tape
Method
-
Mark the stitch line using a ruler and marking pencil along the edge where you want to stitch, about 5 mm from the edge.
-
Mark the stitch holes at equal intervals (usually 4–6 mm apart) along the marked line.
-
Punch the holes using an awl or pricking iron, making sure each hole goes through both pieces of leather if joining two pieces.
-
Thread the needle with a length of thread about three times the length of your stitch line. Tie a small knot at one end.
-
Begin stitching by inserting the needle from the back (inside) to the front (outside) at the first hole.
-
Continue stitching by pushing the needle down through the second hole from front to back, then up through the third hole from back to front. Carry on in and out along the line; this makes a running stitch. For a back stitch, come up one hole ahead and go down through the hole behind, so that the stitches touch end to end on the front. For a saddle stitch, tie no knot: put a needle on each end of the thread and pass both needles through every hole, one from each side.
-
Maintain even tension – pull the thread gently and consistently. Too tight will pucker the leather; too loose will leave ugly loops.
-
Finish the seam by stitching back through the last two or three holes to lock the thread, or by tying a secure knot on the back. Trim the thread close to the leather.
- Always use a thimble to protect your fingers when pulling needles through tough leather.
- Push the awl away from your body and keep your other hand out of its path. When striking a pricking iron, use a mallet and keep your fingers clear.
- Never hold needles in your mouth; keep them in a needle case and count them before and after work.
- Wear safety gloves when handling sharp tools.
- Keep your workbench tidy and free of loose thread scraps.
- Sit properly on the workshop stool while working.
For a needle prick or a small cut, stop work, wash the wound with clean water and soap, press on it with a clean cloth until the bleeding stops, and cover it with a clean dressing. Report every injury to the person in charge of the workshop. A deep cut, or a broken needle point left in the skin, needs attention at a health facility.
- Put thread ends and small leather scraps in the dustbin, and keep larger offcuts for practice pieces
- Put bent or broken needles in a closed tin before they are thrown away
- Wipe the awl, pricking iron, scissors and ruler with a dry cloth, then wipe the workbench and sweep the floor
- Store needles in their case, thread on its reel and tools in their proper places, in a dry cupboard so that they do not rust
In a workshop, most joined stitches are made by machine. A sewing machine makes a lockstitch with two threads, one from the needle above and one from the bobbin below. The main types used for leather are:
- Flat-bed machine – has a flat table; used for flat work such as wallets, belts and bag panels.
- Post-bed machine – the work sits on a raised post; used for shoe uppers and other shaped work.
- Cylinder-arm machine – has a narrow arm; used for bags and other hollow or tube-shaped items.
A machine may be driven by hand, by a foot treadle or by an electric motor. Hand stitching is learned first because it teaches you to control stitch length, spacing and tension.
- Unequal spacing between stitches
- Pulling stitches too tightly, causing the leather to pucker
- Using thread that is too thick or too thin for the leather thickness
- Skipping holes, which weakens the seam
Practice exercise: Cut two rectangular sample pieces from scrap leather (each about 10 cm × 5 cm). Mark a line 5 mm from one long edge on both pieces. Align the edges and hold them together with clamps or clips, because pins leave permanent holes in leather. Punch holes at 5 mm intervals along the marked lines. Join the two pieces using a running stitch, keeping your stitches uniform in size and tension. Trim any excess thread when finished.
In Tanzania, leather artisans in places like Arusha and Morogoro use joined stitches to make strong, long-lasting sandals, belts and bags. When a cobbler repairs a torn leather strap on your school bag or fixes the stitching on your mother's sandals, joined stitches ensure the repair holds up under daily use. Learning this skill could also help you start a small shoe repair or leather craft business in your village or town.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select materials
- Select tools and equipment
- Interpret working drawings or patterns
- Select types of stitches
- Select the correct types of needles
- Select thread to suit the type of leather, fabrics and needle sizes
- Construct stitches using a single or double thread
- Cut a sample of leather
- Make consistent stitch length and width
- Observe safety precautions
- Clean the workplace
- Clean tools and equipment
- Store tools and equipment
Tathmini ya matokeo
A piece of leather or fabric is joined by joined stitches
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should clearly explain:
- How to select different types of needles, stitches, threads suitable for different types of leathers
- Types of sewing machines
- Procedures of making different types of stitches
Principles: The student should explain the principles of:
- Hand stitching
- Adjusting stitch lengths
Theories: The student should clearly explain:
- The difference between temporary, joining and decorative stitches
- The relationship between threads and needles
- The relationship between materials, needles and threads
- The importance of precise and detailed work while making stitches
Circumstantial knowledge:
Detailed knowledge of:
- Safety precautions on sewing operation
- Safe handling of tools and equipment
- First aid
- Waste disposal
Swali
What are joined stitches in leather work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado