Mada za sehemu hiiMaking simple designs of footwearMada 4
- Designing a simple derby shoe
- Designing a simple Oxford shoe
- Designing simple sandal
- Designing a simple training shoe
A training shoe (trainer) is a light, flexible, laced shoe made for sport, exercise and everyday wear. Designing one means studying the style, sketching it, and then turning the sketch into flat paper patterns from which the parts of the upper can be cut. Every mistake in a pattern is repeated in every shoe cut from it, so the work must be careful and exact.
- Vamp – the front of the upper, over the toes
- Quarters – the two side parts that run back to the heel
- Toe cap – an extra layer that protects the toe from wear
- Eyelet facing – the strip on each side of the opening that carries the eyelets and laces
- Tongue – lies under the laces and protects the top of the foot
- Heel counter – the stiffened part that supports the back of the heel
- Collar – the soft, padded top edge below the ankle
- Lining and insole – give comfort inside the shoe
- Sole – the bottom part that touches the ground
Before drawing, study a sample shoe or a picture and ask:
- Function – is the shoe for running, gym work or everyday wear?
- Parts – how many pieces make the upper, and which piece lies on top at each seam?
- Materials – soft leather, suede, canvas or synthetic mesh for the upper; fabric for the lining; rubber for the sole
- Size and fit – which shoe last (the foot-shaped form on which the shoe is built) gives the right size and toe shape?
- Style – what colours, stitching lines and decoration will make the shoe attractive?
| Item | Purpose |
|---|---|
| Plastic shoe last | Gives the size and shape of the shoe |
| Measuring tape, steel rulers, square | Measuring and drawing straight lines |
| Pencil, rubber, marker pen | Sketching and outlining |
| Tracing paper | Thin and see-through, for copying shapes and lines |
| Soft manilla sheet | Easy to draw on and cut, for working patterns |
| Hard manilla sheet | Stiff and long-lasting, for master patterns |
| Cutting knife, scissors, cutting board | Cutting patterns |
| Awl, hole punches, hammer | Making marking points |
Step 1: Sketch the design
Draw the side view of the shoe in pencil: the sole line first, then the toe, the top line and the heel. Add the design lines for the toe cap, eyelet facing, quarters, collar and tongue, and mark the eyelets. Name each part with an arrow.
Step 2: Take measurements
With the measuring tape, measure the last: its length from heel to toe along the bottom, its girth around the widest part (the joint) and its girth over the instep. From the sample shoe, measure the height of the back, the length of the lacing opening and the spacing of the eyelets. Write every measurement on the sketch.
Step 3: Copy the shape of the last
Hold tracing paper against the outer side of the last. Make small cuts in the paper at the toe and heel so that it lies flat on the curves, then trace the centre line down the front, the curve of the back, and the bottom edge where the side of the last meets its base. Cut out this shape. It is the flat shape of the side of the shoe.
Step 4: Transfer to soft manilla
Lay the tracing on a soft manilla sheet and draw round it. Using your measurements, draw the design lines from the sketch inside this shape. Along the bottom edge add about 15 mm, called the lasting allowance, which is pulled under the insole when the shoe is made.
Step 5: Cut the master pattern from hard manilla
Place the soft manilla shape on hard manilla, draw round it and prick through the design lines with the awl. Cut it out on the cutting board with a sharp knife, using the steel ruler for straight edges. This master pattern is kept as the reference and is never used for cutting leather.
Step 6: Cut the patterns of the parts
Trace each part from the master pattern onto manilla: vamp, quarter, toe cap, eyelet facing, tongue and heel counter. Where one part lies under another, add about 8 mm to the lower part so that the two can be stitched together.
Step 7: Mark, label and grade
- Marking points: punch the eyelet positions, and prick small holes to show where the toe cap and eyelet facing sit on the parts below them.
- Labels: write on each pattern its name, the style, the size, and how many pieces to cut for a pair.
- Grading: grading means making the same patterns in other sizes. Each continental size is about 6.7 mm longer than the size before it, and the patterns become a little wider in the same proportion. A grading machine does this quickly; by hand, redraw each pattern with the extra length shared evenly along it.
Step 8: Check, sort and store
Lay the patterns together and check that edges which will be joined are the same length. Count the patterns against your list, group them by size, and tie each set through a punched hole or keep it in a labelled envelope. Store patterns flat in a dry place.
A student designs a simple trainer in continental size 40. A size 40 last is about 40 × 6.7 mm = 268 mm long. From the sample shoe the student measures a back height of 60 mm and five eyelets spaced 15 mm apart. After copying the last and drawing the design, the student adds a 15 mm lasting allowance along the bottom edge and 8 mm on the vamp where it lies under the toe cap. To grade the patterns to size 41, the student makes them fit a last 41 × 6.7 mm = about 275 mm long.
- Cut on the cutting board, never on the bare bench, and keep the fingers of your holding hand behind the edge of the ruler.
- Keep the knife sharp, because a blunt knife slips, and cover its blade when it is not in use.
- Hold the awl and punches upright and keep your fingers clear of the hammer.
- Use the grading machine only after you have been shown how.
- When you finish, wipe the last, rulers and cutting board, return every tool to its place, and put paper offcuts in the bin.
- Sketching a shoe that does not match the shape of the last
- Forgetting the lasting allowance, so the upper cannot be pulled under the insole
- Leaving out the allowance where parts overlap
- Patterns with no labels or marking points, which are easily mixed up
Footwear makers in towns such as Arusha and Dar es Salaam design training shoes for school athletes and local football teams. Testing a design with paper patterns first costs very little, and it prevents waste of expensive leather when cutting begins. A person who can sketch a style and turn it into accurate, graded patterns is a valuable worker in any shoe workshop.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student are to be able to correctly:
- Interpret different designs
- Select tools and equipment
- Take measurements of training shoe designs
- Select materials
- Produce basic sketches
- Transfer sketches into soft manilla sheets
- Cut master pattern from hard manilla sheet
- Grade patterns
- Label patterns
- Identify marking points
- Analyse the patterns and sort them out
- Store patterns
- Clean tools, equipment and machines
- Observe safety precautions
- Store tools and equipment
Tathmini ya matokeo
Training shoe are designed according to specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should:
- Explain the concept of training shoe design
- Make patterns for simple training shoes
- Interpret measurements correctly
Principles: The student should explain the principles of:
- Taking measurements
- Sketching and making patterns
- Cutting patterns
- Grading patterns
- Labeling patterns
Theories: The student should explain:
- The types of pattern materials
Circumstantial knowledge:
Detailed knowledge of:
- Safe handling of work tools and equipment
- Safety precautions when making simple training shoes
Swali
Which part of a training shoe is the front of the upper that covers the toes?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado