Mada za sehemu hiiFabricating farm equipmentMada 4
- Fabricating feeders and water trough
- Fabricating nests and cages
- Fabricating yoke and skey
- Fabricating brooder
Feeding and watering equipment are essential farm structures that must be properly designed and constructed to ensure animals receive adequate nutrition and water while minimizing wastage. This study note covers the fabrication of feeders and water troughs for different types of livestock, focusing on practical procedures and materials suitable for Tanzanian farming conditions.
Feeders and water troughs are farm equipment used to provide feed and water to livestock. Proper fabrication of these structures is important because:
- They ensure animals have consistent access to clean water and nutritious feed
- They help reduce feed and water wastage, saving money
- They improve animal health and productivity
- They make farm management easier and more efficient
Regardless of the animal type, all feeders and water troughs must meet three primary conditions:
- Easy access: Allow the animal to access the feed or water easily and comfortably without strain or injury
- Minimal wastage: Minimize feed or water wastage through proper design and construction
- Easy maintenance: Easy to clean and safe for the operator to handle
Materials Required
The main feed for cattle, sheep and goats is forage (grass, hay, silage). Common materials for constructing troughs include:
- Cement, sand, and aggregate (for concrete troughs)
- Timber planks
- Blocks
- Measuring tools (tape measure, spirit level)
- Carpentry tools (hammer, saw, nails, screws)
Construction of Troughs and Racks for Cattle
Location: Place troughs or racks in front of the resting area of the animals. The person delivering feed should remain safe, and animals should not be disturbed while feeding.
Designing troughs: Outdoor troughs are usually designed to be used from at least two sides. If the trough is shared by animals in adjacent paddocks, a barrier (such as a wall or hanging fence) must separate the two sides to prevent animals from mixing.
Designing racks: Racks are used for hanging hay or forage. When wall-mounted, the rack may be accessed from three free sides. Mobile free-standing racks allow feed access from all sides. The rack should be high enough for animals to reach and pull the feed comfortably.
Construction of Troughs and Racks for Sheep and Goats
Feed and water troughs for sheep and goats are similar to cattle troughs but with smaller dimensions due to the smaller size of these animals.
Tombstones: In both concrete and timber feed troughs for goats and sheep, it is important to add barriers called "tombones" that restrain the animals while feeding. This is especially important for goats to minimize feed wastage. Without barriers, goats may climb into troughs, disturb one another, and soil the feed with faeces and urine.
Simple wooden troughs for grain and mineral supplements:
A simplified wooden trough can be constructed using timber and nails to form a shallow channel with the following dimensions:
- Depth: 25-30 cm
- Width: 20-25 cm
- Length: 40 cm × number of animals
Example: For a farmer with 10 adult goats or sheep, the trough should be: 25−30 cm (depth)×20−25 cm (width)×400 cm (length)
This ensures each animal has enough space to access the feed without crowding.
Types of Poultry Feeders
The type of feeder required depends on the stage of growth of the chickens:
- Chick feeders: For young chicks in brooding
- Grower feeders: For growing birds
- Layer feeders: For mature laying hens
Homemade Chick Feeders
In deep litter systems, homemade chick feeders can be made from plastic bottles punched with holes on the sides. The holes must be:
- Large enough for chicks to reach the feed
- Small enough to prevent chicks from entering the container
For battery cages, feed channels are placed on the periphery of the cage.
Procedure for Fabricating Semi-Automatic Poultry Feeders and Drinkers
Materials needed:
- Two used one-litre plastic bottles
- Plastic plates with raised brims
- Soldering gun or 4mm iron rod
- 4mm bolt and nut with metal and rubber washers
Procedure:
- At the centre of both bottles' floors, punch a hole using a 4mm hot iron rod or soldering gun. Do the same at the centre of the plastic plates.
- For the first bottle, cut 4 equally spaced holes each about 3-4cm wide just above the bottom floor.
- For the second bottle, punch a 3-4mm hole close to the very bottom.
- Insert the 4mm bolt through the central hole of the plastic plate and attach to the bottle.
- Tighten the bolt using the nut with washers to connect the bottle to the centre of the plate. Repeat for both bottles.
- Ensure the cone at the bottom of the bottle is not flattened when tightening.
- Keep the assembled drinker and feeder suspended just high enough for chicks to reach the feed easily.
Construction of Conventional Wooden Feeders for Chicken
Materials needed:
- Timber planks or off-cuts
- Nails or screws
- Hammer or screwdriver
- Saw
- Measuring tape
- Sandpaper
- Hinges
- Paint or wood sealant
Procedure:
-
Design and measurements: Decide on feeder size based on number of chickens. Typical dimensions:
- Length: 60-80 cm
- Width: 20-25 cm
- Height: 20-25 cm
-
Cut the timber: Cut into flat pieces:
- Base (feeding tray)
- Two long side panels
- Two short end panels (may be slanted for better access)
- Optional: lid or top panel
-
Prepare the pieces: Sand edges and surfaces smooth. Optionally treat or seal the wood for durability.
-
Assemble: Attach side panels to the base using nails or screws. Attach end panels to complete the feeder box. Ensure the structure is sturdy.
-
Add feeding trough design: Angle side panels slightly or notch them at the top to prevent feed spillage.
-
Create access openings: Make small openings or cutouts on the sides for chickens to access the feed.
-
Add lid: Attach a hinged lid on top to protect feed from rain and contamination. Make it easy to open for refilling.
Making Chicken Feeders Using Local Materials
Farmers can use various locally available materials to make feeders:
- Split bamboo
- Plastic pipes of appropriate diameter
- Galvanized roof gutters
- Plastic containers
- Used timber from construction sites
These alternative materials help reduce costs while still providing effective feeding solutions for poultry.
A small-scale poultry farmer in Mwanza can fabricate their own wooden feeders and water troughs using locally available timber off-cuts and simple tools. For example, constructing a 60cm wooden feeder for 50 layer chickens costs approximately TZS 15,000-20,000 in materials, compared to buying a commercial feeder for TZS 40,000-50,000. This saves money and allows the farmer to replace worn equipment without depending on external suppliers.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select work tools, equipment, and safety gears
- Design farm equipment
- Fabricate farm equipment as per design
- Keep different records
- Clean tools, equipment used and work place
- Store tools and equipment
Tathmini ya matokeo
Feeders and water trough fabricated as per the required standards.
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should elaborate how to Fabricate feeders and water trough
Principles: The student should explain principles involved in fabricating feeders and water trough
Theories: The student should :
- Present advantages of using fabricated equipment
- Elaborate different ways of designing of different farm equipment
- Explain fabrication materials
- Highlight the importance of keeping different records
Swali
What are the three primary conditions that all feeders and water troughs must meet regardless of the animal type?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado