Mada za sehemu hiiPerforming irrigationMada 3
- Performing furrow/surface irrigation
- Performing sprinkler irrigation
- Performing drip irrigation
Sprinkler irrigation is a method of applying water to crops in the form of spray, similar to natural rainfall. Water is pumped through pipes and sprayed over the crops using sprinklers. This method is useful when crops need gentle, even watering and when the farmer cannot use surface irrigation methods like flooding.
Sprinkler irrigation is a water application method where water is distributed through a system of pipes and sprinklers. The water is pumped under pressure and sprayed into the air, falling onto the crops like rain. The water breaks into small droplets that moisten the soil evenly. When it is applied at the right rate, it does not cause soil erosion or waterlogging.
Before performing sprinkler irrigation, gather the following tools and materials:
- Water source: A river, well, borehole or dam, and a water storage facility such as a tank or reservoir
- Pump: Water pump to create pressure for spraying water
- Pipes: PVC pipes and hose pipes to carry water from the source to the field
- Sprinkler heads: Sprinkler irrigation kit including sprinkler heads and misters (misters give a very fine spray and are used mainly for seedlings in the nursery)
- Filters: To clean water and prevent clogging of sprinkler nozzles
- Hand tools: Screwdriver, spanners, hand hoes, and forks for installation and maintenance
- Safety gear: Gum boots and overalls to protect the operator
Follow these steps carefully to carry out sprinkler irrigation properly:
Step 1: Prepare the Site
Clear the area where sprinklers will be placed. Remove any obstacles that might block the spray pattern. Mark positions for sprinkler heads according to the spacing plan.
Step 2: Install the Pipeline System
Lay PVC pipes from the water source to the field. Connect sections using appropriate fittings. Ensure all joints are tight and secure to prevent water leakage.
Step 3: Install Sprinkler Heads
Attach sprinkler heads at marked positions along the pipeline. Each sprinkler should be positioned at the correct height and angle for even water distribution.
Step 4: Connect the Pump
Connect the water pump to the pipeline system. Prime the pump by filling it with water before starting. This removes air and ensures proper suction.
Step 5: Install Filters
Fit a strainer on the end of the suction pipe and a filter on the main pipe just after the pump. Filters prevent dirt and particles from clogging the system.
Step 6: Test the System
Before closing the ends of the pipes, run water through them for a few minutes to flush out soil. Then close the ends, start the pump at low pressure and check for leaks. Adjust sprinkler heads to ensure proper spray coverage. Increase pressure gradually to operating levels.
Step 7: Operate the System
Run the sprinkler system for the required duration based on crop water needs. Monitor the system throughout the irrigation cycle.
Step 8: Shut Down and Store
After irrigation, switch off the pump. Drain the water from the pipes so that dirt does not settle and algae do not grow inside them. Clean filters and store equipment properly.
- Give the crop the amount of water it needs: too little causes wilting, while too much wastes water, washes nutrients out of the root zone and can cause waterlogging
- Apply water no faster than the soil can absorb it, so that it does not run off and erode the soil
- Space the sprinklers so that their sprays overlap; this gives even wetting
- Irrigate early in the morning or late in the afternoon, when wind and evaporation are low. Morning is better for many crops, because leaves that stay wet through the night are more easily attacked by fungal diseases
- After irrigating, dig a small hole to check that the water has reached the root zone
- Follow the rules of the water source and of the irrigation scheme: take water only on your allocated days and times, obtain a water-use permit from the water authority where one is required, do not waste water, and do not damage or tamper with shared pipes, canals and valves
- Wear gum boots and overalls when operating the system
- With the power switched off, look at the cable, plug and switch of an electric pump for damage before use; never touch them with wet hands, and report any fault so that a qualified electrician can repair it
- Run an engine-driven pump in the open air, and refuel it only when the engine is stopped and cool
- Keep hands away from rotating parts of the pump
- Ensure pipelines are properly secured to prevent tripping hazards
- Never run the pump dry as this damages the seals
- Provides even water distribution across the field
- Saves water compared to surface flooding methods
- Can be used on uneven terrain where surface irrigation is difficult
- Allows controlled application of water at any time
- Reduces labour requirements once installed
- Can be used to apply fertilisers through the system (fertigation)
- Initial cost of equipment is high
- Requires a reliable power source for the pump
- Wind can affect spray distribution pattern
- Water loss through evaporation, especially in hot conditions
- Regular maintenance is needed to keep the system working
- Wetting the leaves can encourage fungal diseases in some crops, such as blight in tomato
A farmer in Morogoro wants to irrigate a cabbage plot measuring 20 metres by 15 metres using sprinkler irrigation. The farmer plans to give the crop 30 millimetres of water each week, in two irrigations of 15 millimetres each (these figures are an example; the real need depends on the crop, the soil and the weather). The system has:
- Six sprinklers, set out in two rows of three so that the spray of each sprinkler reaches the next one
- A discharge of 500 litres per hour from each sprinkler at its working pressure
- A pump that keeps the pressure steady at the level the sprinkler maker recommends
Step 1: Area of the plot
20 m × 15 m = 300 m²
Step 2: Water needed for one irrigation
A depth of 15 mm is 0.015 m, so the volume is 300 m² × 0.015 m = 4.5 m³, which is 4,500 litres.
Step 3: Water delivered each hour
6 sprinklers × 500 litres per hour = 3,000 litres per hour
Step 4: Running time
4,500 litres ÷ 3,000 litres per hour = 1.5 hours (1 hour 30 minutes) for each irrigation
Step 5: Water needed each week
2 irrigations × 4,500 litres = 9,000 litres per week
So the farmer needs a tank or other supply that can give at least 4,500 litres for each irrigation. Some water is lost to wind and evaporation, so in practice the farmer checks how deep the soil is wet after irrigating and adds a little running time if needed.
A pump lifts water from the source and pushes it through the pipes under pressure. The common types on small farms are:
- Engine-driven centrifugal pump (petrol or diesel): easy to move from place to place. Before starting, check the engine oil and the fuel, and prime the pump. Change the oil and clean the air filter at the intervals given in the maker's manual.
- Electric pump (surface or submersible): used where there is mains or solar power. A submersible pump works under water in a well or borehole. Keep the cable, plug and switch dry, and leave all wiring and electrical repairs to a qualified electrician.
- Manual pump (treadle or hand pump): gives low pressure and suits only very small plots. Keep the moving parts greased and replace worn seals and valves.
For every pump: keep the suction strainer clear, stop the pump at once if it makes an unusual noise or stops delivering water, tighten loose bolts and hose clips with the right spanner or screwdriver, and write down each service.
Irrigation water can be stored in plastic or metal tanks, concrete or masonry tanks, lined ponds and small dams (reservoirs). To maintain a storage facility:
- Keep tanks covered to keep out dirt, leaves and mosquitoes and to slow the growth of algae
- Wash the sludge out of tanks from time to time, and remove silt and weeds from ponds
- Check for cracks and leaks, and repair pond linings, taps and tank fittings promptly
- Fence open ponds and dams so that children and animals cannot fall in
- Clean filters weekly to prevent clogging
- Check pipe joints for leaks after each use
- Clean blocked sprinkler and mister nozzles by soaking them in clean water and using a soft brush or a wooden toothpick; never use wire or a nail, which enlarges the hole and spoils the spray pattern
- Check that each sprinkler turns freely, and replace worn nozzles, springs and washers
- After use, flush the pipes with clean water, especially after applying fertiliser through the system, and then drain them
- Wash the soil off hand hoes, forks, spanners and other tools, dry them and return them to the toolbox
- Replace worn sprinkler heads promptly
- Store pipes flat or on racks in the shade (sunlight makes PVC brittle), coil hose pipes without kinks, and keep the sprinklers, the pump and the tools in a dry, locked store
A small-scale vegetable farmer in Arusha can use sprinkler irrigation to water crops like cabbages, carrots, and leafy vegetables during the dry season. By installing a simple system with a water pump, PVC pipes, and three or four sprinkler heads that are moved from one position to the next, the farmer can efficiently irrigate a quarter-acre plot. This method saves labour compared to manual watering with buckets, allowing the farmer to tend to other tasks while ensuring crops receive adequate water for good growth and higher yields at market.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Organise working tools, equipment and machineries
- Perform sprinkler irrigation
- Maintain irrigation tools, equipment and machineries
- Operate and maintain different types of water pumps
- Maintain water storage facilities
- Maintain sprinklers
- Observe safety precautions in handling tools and equipment
- Clean irrigation facilities
- Store irrigation facilities
Tathmini ya matokeo
Sprinkler irrigation designed according to the required horticultural crop practices
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to carry out sprinkler irrigation
Principles: The student should explain the principles of Irrigating field/farms.
Theories: The student should explain:
- Importance of sprinkler irrigation method
- How to conduct sprinkler irrigation
- Advantages of sprinkler irrigation
- How to maintain different types of water pumps.
- Type of water storage facilities
- How to construct irrigation sprinkler irrigation
Circumstantial knowledge: Detailed knowledge about observing farm/field irrigation facilities rules and regulations.
Swali
What is sprinkler irrigation?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado