Mada za sehemu hiiPerforming irrigationMada 5
Surface irrigation is a method of applying water to farmlands by allowing water to flow across the soil surface, using gravity to spread water to crops. It is one of the oldest and most widely used irrigation methods in Tanzania, especially for crops grown in flat or gently sloping fields. This method is cost-effective and suitable for small-scale farmers who rely on available water sources like rivers, dams, or wells.
Surface irrigation is the deliberate application of water to the soil surface so that it infiltrates and reaches the plant root zone. The water moves across the field by gravity flow, wetting the soil as it advances. This method relies on the natural slope of the land to distribute water evenly across the cultivated area.
There are three main types of surface irrigation used in Tanzania:
1. Basin Irrigation
Water is applied to flat, enclosed areas (basins) surrounded by low earth banks. The basin is flooded with water, which then slowly infiltrates into the soil. This method works well for crops that require standing water, such as rice.
2. Furrow Irrigation
Small channels or furrows are dug between crop rows. Water is directed into these furrows and flows along them, soaking the soil on both sides to reach the plant roots. This method is ideal for row crops like maize, tomatoes, and beans.
3. Border Irrigation
The field is divided into rectangular strips (borders) separated by small levees. Water is released at the upper end and flows down the border strip, wetting the soil as it moves. This method suits crops planted in rows on gently sloping land.
Surface irrigation is appropriate for a wide range of field crops grown in Tanzania, including:
- Maize
- Rice
- Beans
- Wheat
- Sorghum
- Millet
- Cotton
- Sunflower
- Vegetables such as tomatoes, onions, and cabbages
A good surface irrigation system should have the following features:
- Proper field layout: The field should have a uniform slope (usually between 0.1% and 2%) to allow even water distribution
- Good soil infiltration rate: The soil should absorb water at a moderate rate to prevent runoff or waterlogging
- Adequate water supply: A reliable source of water such as a river, dam, borehole, or rainwater harvesting structure
- Proper land preparation: Well-leveled fields with appropriate furrows, basins, or borders
- Good drainage: Proper drainage to remove excess water and prevent waterlogging
To perform surface irrigation, the following items are required:
Personal Protective Equipment (PPE):
- Overalls (to protect clothing)
- Gloves (to protect hands)
- Gum boots (to keep feet dry and protected)
- Caps (to protect from sun)
Tools and Equipment:
- Hand hoes (for digging furrows and shaping borders)
- Water pump (to draw water from the source)
- Pipes or channels (to convey water to the field)
- Spades (for earthwork and shaping basins)
- Rakes (for leveling)
Proper field preparation is essential for effective surface irrigation. Follow these steps:
Step 1: Clear the field Remove all weeds, crop residues, and stones from the field.
Step 2: Level the field Use a hoe or rake to level the soil surface. Uneven surfaces cause water to collect in low spots, leaving some areas dry.
Step 3: Design the irrigation layout Choose the appropriate type of surface irrigation (basin, furrow, or border) based on the crop and land slope.
Step 4: Construct furrows, basins, or borders Using hand hoes and spades, create the irrigation structures:
- For furrow irrigation: Dig furrows about 30 cm deep and 60 cm apart
- For basin irrigation: Form square or rectangular basins surrounded by low earth banks
- For border irrigation: Create long strips separated by levees
Step 5: Connect water source Set up the water pump and lay pipes or channels to bring water from the source to the field.
Once the field is prepared, follow these steps to apply water:
Step 1: Assess soil moisture Check the soil moisture content before irrigating. The soil should be dry enough to need water but not cracked or too dry.
Step 2: Start water flow Turn on the water pump and allow water to flow into the irrigation channels or directly into the furrows, basins, or borders.
Step 3: Monitor water distribution Watch as water moves across the field. Ensure water reaches the far end of the field without causing excessive runoff.
Step 4: Control the flow rate Adjust the water flow to maintain a steady advance across the field. Too fast causes runoff; too slow may not reach the end.
Step 5: Stop irrigation when sufficient When water has advanced to about 80% of the field length and the soil is thoroughly moist, stop the water flow.
Step 6: Allow drainage Allow excess water to drain away to prevent waterlogging and root damage.
A farmer has a maize field prepared with furrow irrigation. The field is 50 meters long and 20 meters wide. Water flows into the furrows at a rate of 10 liters per minute. If the farmer wants to apply 50 mm of water to the field, how long should the irrigation last?
Solution:
First, calculate the area of the field: Area = 50 m × 20 m = 1,000 m²
Convert 50 mm to meters: 50 mm = 50 ÷ 1000 = 0.05 m
Volume of water needed: Volume = Area × Depth = 1,000 m² × 0.05 m = 50 m³
Convert cubic meters to liters: 50 m³ × 1,000 = 50,000 liters
Time needed = Volume ÷ Flow rate Time = 50,000 liters ÷ 10 liters/minute = 5,000 minutes
Convert to hours: 5,000 ÷ 60 ≈ 83 hours (impractical — this shows why farmers apply water in shorter sessions over several days)
In practice, farmers apply water in batches, allowing each section to absorb water before reapplying.
When performing surface irrigation, always observe the following safety measures:
- Wear protective clothing (overalls, gum boots, gloves, and caps)
- Handle tools carefully to avoid injuries
- Ensure the water pump is properly grounded and operated by trained persons
- Avoid working in wet fields during thunderstorms
- Keep electrical equipment away from water to prevent shocks
In many villages across Tanzania, smallholder farmers use surface irrigation to grow vegetables like tomatoes, onions, and peppers during the dry season. For example, a farmer in Morogoro Region may prepare furrow irrigation in a 0.5-hectare plot, using a water pump to draw water from a nearby river. By properly applying water every 3-4 days during the dry months, the farmer can harvest and sell vegetables at local markets, earning an income to support their family and pay school fees for their children.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Select crop for surface irrigation
- Apply surface irrigation
- Determine the amount of water
- Observe safety precaution.
- Clean the tools
- Store tools
Tathmini ya matokeo
Surface irrigation performed as per laid down crop husbandry practices
Tathmini ya maarifa
Knowledge Evidence
Detailed knowledge of:
Method used: The student should be able to explain how to apply water to the plants
Principles: The student should explain the principles of performing surface irrigation techniques
Theories: The student should explain:
- Quality of irrigation water
- Surface irrigation
- Crop water requirement
- Irrigation frequency
- Importance of irrigation
Circumstantial knowledge: Detailed knowledge about safety precautions in water application
Swali
Which of the following describes surface irrigation?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado