Mada za sehemu hiiPreparing preservative solutionsMada 4
Wood Treatment Methods
Wood treatment is the process of applying chemical preservatives to timber to protect it from fungal decay, insect attacks, and marine borers. This treatment extends the life of wood structures and reduces replacement costs.
Wood treatment methods are classified into two main categories:
- Non-pressure methods – preservatives are applied using brushing, spraying, dipping, or soaking
- Pressure methods – preservatives are forced into wood using high-pressure systems in closed chambers
The choice of method depends on the type of wood, its intended use, and the level of protection required.
Non-pressure methods are simpler and less expensive but generally provide lower retention and shallow penetration.
Brushing
The preservative is applied with a brush to clean, dry timber. This is the simplest method but does not penetrate deeply into the wood. Multiple applications may be needed for effective protection.
Deluging (Spraying)
Preservative is sprayed onto wood using spray nozzles or jets. This method is faster than brushing and is commonly used for treating fencing panels and large surfaces.
Immersion (Dipping)
Timber is submerged in a tank of preservative for a short period, typically 3 to 60 minutes. The treated timber is then allowed to drain. This method provides better penetration than brushing or spraying, especially into checks and end grain.
Steeping
Timber is immersed in preservative for extended periods – from several hours to days or weeks. This allows deeper penetration than immersion. The absorption rate is highest during the first three days, then continues at a decreasing rate.
Pressure treatment is one of the most effective methods for preserving wood. It involves forcing chemical preservatives deep into the wood fibres using high-pressure systems in closed chambers.
Key Features
- Achieves deeper and more uniform penetration
- Higher absorption of preservatives
- Treatment conditions can be controlled to vary retention and penetration
- Suitable for large-scale production
Types of Pressure Treatment
- High pressure: Above 5 bars
- Low pressure: Below 5 bars
Disadvantages
- High initial equipment costs
- Higher energy costs
Before treatment, the preservative solution must be properly prepared by measuring its strength and calculating the correct dosage.
Solution Strength
Solution strength refers to the concentration of active preservative chemicals in the liquid. It is expressed in:
- Grams per litre (g/l), or
- Percentage (%)
The relationship between these units is: g/l=%×10
For example, a 6.5% solution equals 65 g/l.
Measuring Solution Strength: The Hydrometer Test
A hydrometer is a calibrated glass instrument used to measure the specific gravity of liquids, which indicates solution concentration.
Procedure:
- Rinse the hydrometer with distilled water to avoid contamination
- Pour the preservative solution into a clean, tall measuring cylinder
- Lower the hydrometer gently into the liquid – it must not touch the cylinder sides
- Allow the hydrometer to settle and float freely
- Read the scale at the surface of the liquid – this is the specific gravity
- Use a hydrometer chart to convert the reading to solution strength
Important: Temperature affects density readings, so use a thermometer alongside the hydrometer.
Worked Example: Calculating CCA Required
Problem: Calculate the amount of CCA required for a treatment vessel containing 26,605.154 litres of water with a concentration of 79 g/l.
Solution:
Multiply the volume of water by the concentration: 26,605.154×79=2,101,807.166 g
Convert to kilograms: 2,101,807.166÷1000=2,101.8 kg
Answer: 2,101.8 kg of CCA concentrate is required.
The dosage of preservatives depends on three main factors:
1. Wood Species
Some woods absorb preservatives more easily. For example, pine absorbs preservatives more readily than denser woods like oak.
2. Retention Level
Retention is the amount of preservative that must remain in the wood, measured in:
- Pounds per cubic foot (pcf), or
- Kilograms per cubic metre (kg/m³)
Higher retention is required for ground contact or marine applications:
- Above-ground use: 0.25 pcf (4 kg/m³)
- Ground contact: 0.40 pcf (6.4 kg/m³) or higher
Note: 1 lb/ft³ ≈ 16.0185 kg/m³
3. Concentration of Preservative
The solution strength must be correct for effective treatment. Stronger solutions generally lead to higher preservative uptake.
| Preservative | Type | Common Uses |
|---|---|---|
| CCA (Copper Chrome Arsenate) | Water-borne | Transmission poles, exterior wood |
| ACQ (Ammonia Copper Quaternary) | Water-borne | Decking, fencing, residential use |
| Creosote | Oil-borne | Railway ties, utility poles |
| Borates | Water-borne | Interior wood, framing |
- Wear appropriate PPE: gloves, safety goggles, dust mask
- Work in well-ventilated areas
- Avoid inhalation of sawdust from treated wood
- Wash hands before eating, drinking, or using toilet facilities
- Store treated timber in well-ventilated areas
- Do not burn treated timber – harmful chemicals may be released
In Tanzania, carpenters and builders regularly treat wood with preservatives like CCA or creosote to protect roofing timbers, fence posts, and transmission poles from termite attacks and fungal decay. For example, a small-scale builder in Dar es Salaam treating 50 pine poles for a farm fence would need to calculate the correct preservative dosage using the volume of wood and solution concentration to ensure long-lasting protection, avoiding premature replacement costs that could amount to hundreds of thousands of Tanzanian shillings.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools for treating wood
- Treat wood
- Observe safety
- Clean tools
- Store tools
Tathmini ya matokeo
Treatment methods well performed as per technical specification
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The students should explain how to:
- Select proper tools for treating wood
- Treat wood
Principles: The student should explain principles of determining moisture content of timber and poles
Theories: The student should explain procedures for performing wood treatment methods
Detailed knowledge about: Safety precautions involved in performing treatment
Swali
What does the term solution strength refer to in wood preservative treatment?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado