Mada za sehemu hiiProcessing wood by-productsMada 5
Adding value to wood by-products means turning waste materials like sawdust, wood chips, and bark into useful and marketable products. This process increases profitability, reduces waste, and supports environmental conservation. Common value-added products include wood pellets, briquettes, charcoal, particleboard, and animal bedding.
Briquettes are compressed blocks of biomass materials used as fuel for cooking or heating. The process involves collecting raw materials, drying them, grinding, and pressing them into dense blocks.
Key Steps in Briquette Making
-
Collect raw materials – Gather sawdust, wood shavings, or agricultural waste. The material must be free from contaminants like metal, plastic, and stones.
-
Dry the materials – Reduce moisture content to 8–10%. If too wet, the briquettes will be weak and the machine will not work properly. Dry by spreading in the sun or using a mechanical dryer.
-
Sieving – Remove unwanted materials and sort particles by size. The ideal particle size ranges from 0.1 mm to 4 mm for uniform briquettes.
-
Grinding – Crush materials to create homogeneous particles. This increases surface area and makes the material easier to compress.
-
Pressing for compaction – Use a briquetting machine (piston press or screw extruder) to compress the material under high pressure. The pressure causes the natural resins in wood to act as a binder, holding the pieces together without additional substances.
-
Cooling – Allow the formed briquettes to cool in ambient air. This hardens them and improves their shape and stability.
Example: Processing Sawdust into Briquettes
A student visits a local sawmill and collects 10 kg of sawdust. The sawdust has 25% moisture content. To meet the required 8–10% moisture content for effective briquetting, the student spreads the sawdust under direct sunlight for 3 hours. After drying, the moisture content drops to 9%. The dried sawdust is then sieved to remove larger wood pieces and ground to a consistent particle size. Finally, the material is fed into a screw extruder machine to produce cylindrical briquettes with a density of 1.0 g/cm³.
| Technology Type | Pressure | Production Capacity | Binder Required |
|---|---|---|---|
| Large-scale (high-pressure) | ~1000 kg/cm² | 250–3000 kg/h | No |
| Medium-scale | 25–250 kg/h | Low to moderate | Sometimes |
| Small-scale (hand-operated) | 10–1000 kg/cm² | ~5 kg/h | Yes |
Binders hold materials together, especially when pressure is low. Good binders are affordable, readily available, and produce clean-burning fuel.
Types of binders:
- Organic binders – Starch (from maize, cassava, or wheat), molasses, and animal dung. These burn cleanly and add energy value.
- Inorganic binders – Clay and cement. These increase ash content and may reduce combustion efficiency.
Starch binder preparation: Mix starch powder with cold water, then heat while stirring until a gelatinised solution forms. A 10–25% concentration is suitable. If too dilute, the briquettes will be weak. If too thick, the paste will not mix evenly with the biomass.
Charcoal is produced by heating wood in a limited oxygen environment (pyrolysis) at temperatures of 350°C to 450°C. This removes water and volatile substances, leaving pure carbon.
Charcoal-Making Process
-
Collect raw materials – Use branches, treetops, slabs, offcuts, or sawdust from forests or sawmills.
-
Size the materials – Cut branches and offcuts to at least 0.3 metres in length for the kiln.
-
Dry the materials – Reduce moisture to 15–20%. Moisture above 25% causes excessive smoke and longer burning times. Below 10% risks over-burning and cracking.
-
Arrange in kiln – Place large-diameter pieces at the base, then stack smaller pieces on top.
-
Carbonise – Heat the kiln while restricting oxygen. For modern steel kilns, this takes about 48 hours. Monitor smoke colour – it changes from dense white to light blue when carbonisation is complete.
-
Cool and offload – Seal the kiln and allow it to cool. Open carefully and separate charcoal from unburned wood and dust.
Before packaging, test the following parameters:
- Density – Should range from 800 to 1200 kg/m³. Higher density means slower burning and better handling.
- Moisture content – Must be 5–8% for efficient burning.
- Burning time – Duration the briquette produces heat after ignition.
- Ash content – Should be between 1% and 15%. High ash reduces efficiency.
- Calorific value – Measured in kJ/kg, indicates heat energy released.
Package briquettes in plastic bags, paper bags, or jute bags. The label must show:
- Type of biomass material used
- Weight of the package
- Name and address of manufacturer
- Instructions for use and storage
- Safety precautions
Store in a cool, dry place with temperature between 10°C and 25°C and humidity below 50%.
- Wear gloves, overalls, safety helmet, safety boots, and eye glasses
- Use a dust mask to protect against wood particles
- Be careful of extreme heat from machines and kilns
- Handle electrical parts with caution
- Ensure good ventilation in the working area
A small-scale entrepreneur in Mwanza can collect sawdust from local carpentry workshops for free or at low cost, then process it into charcoal briquettes using a simple hand-operated press. If each kilogram of sawdust yields 0.8 kg of saleable briquettes sold at TZS 1,500 per kg, processing 50 kg of sawdust weekly generates approximately TZS 60,000 in additional income while reducing environmental pollution from wood waste.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Add value to wood
- Testing the quality of processed
- Adhere to safety principles
- Clean tools
- Store tools
Tathmini ya matokeo
Value to wood by-products - Select tools and products added value according to technical specifications.
Tathmini ya maarifa
Wood by-knowledge of:
Method used: The students should explain how to:
- Select tools and equipment for adding value to wood by-products
- Add value to
- Adhere to safety principles
Principles: The student should explain the principles of adding value to wood by-products.
Theories: The explain:
- Methods of processing
- Techniques of
- Uses of wood
- Conditions to store added value products
Circumstantial knowledge:
Detailed knowledge about: Safety precautions involved in handling wood by-products.
Swali
What is the ideal moisture content of wood waste before it is fed into a briquetting machine?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado