Mada za sehemu hiiDesigning and making domestic freezersMada 6
Constructing Refrigerant Pipe Circuit
A refrigerant pipe circuit is the network of tubes that connects the compressor, condenser, evaporator, and other components in a refrigeration system. It allows the refrigerant to circulate continuously, absorbing heat from the inside of the refrigerator and releasing it outside. When we construct this circuit, we join pipes and fittings using appropriate techniques like soldering, brazing, or welding to create a leak-free system.
The basic refrigerant pipe circuit consists of four main parts:
- Suction line – carries low-pressure refrigerant vapor from the evaporator back to the compressor
- Discharge line – carries high-pressure hot vapor from the compressor to the condenser
- Liquid line – carries high-pressure liquid refrigerant from the condenser to the evaporator
- Connecting fittings – elbows, tees, and reducers that allow pipes to change direction or size
Before constructing a refrigerant pipe circuit, gather these tools:
- Measuring tools: Tape measure, thermometer
- Cutting tools: Pipe cutter or hacksaw
- Bending tools: Bending machine or spring bender
- Joining tools: Oxy-acetylene plant (for brazing), soldering gun, resistance welding machine
- Fastening tools: Pop rivet gun
- Finishing tools: Shearing machine, spray painting compressor
- Safety gear: Protective gloves, goggles, welding helmet, fire extinguisher
Step 1: Planning and Measuring
- Read the refrigerator design drawing to determine pipe lengths and sizes
- Measure each pipe section accurately using a tape measure
- Mark cut points clearly with a marker
Step 2: Cutting the Pipes
- Use a pipe cutter or hacksaw to cut pipes to the required lengths
- Ensure cuts are square and clean
- Remove burrs from inside and outside the pipe using a deburring tool
Step 3: Bending the Pipes
- Use a bending machine or spring bender to form bends
- Avoid kinks or wrinkles that restrict refrigerant flow
- Maintain proper bend radius (typically 3 to 5 times the pipe diameter)
Step 4: Cleaning and Fitting
- Clean pipe ends and fittings with emery cloth or wire brush
- Apply flux when using soft solder
- Fit all components together and check alignment
Step 5: Joining the Pipes
- Use brazing (with oxy-acetylene) for copper pipes in refrigeration systems
- Heat the joint evenly until the brazing alloy flows into the gap
- Allow joints to cool naturally before moving
- For mechanical connections, use appropriate fittings and sealants
Step 6: Testing for Leaks
- Pressurize the system with nitrogen or dry air
- Use soap solution or electronic leak detector to check all joints
- Repair any leaks found and retest
- Always wear safety goggles and gloves when cutting or bending pipes
- Use fire-resistant blankets when brazing near flammable materials
- Keep a fire extinguisher nearby during welding or brazing
- Ensure proper ventilation in the work area
- Never leave oxy-acetylene equipment unattended while lit
A domestic freezer requires copper pipes with the following measurements:
- Suction line: 800 mm
- Discharge line: 600 mm
- Liquid line: 400 mm
Solution:
-
Calculate total pipe length: 800 + 600 + 400 = 1800 mm (1.8 meters)
-
Determine pipe sizes (typical for domestic freezer):
- Suction line: 3/8 inch (outer diameter)
- Discharge line: 1/4 inch
- Liquid line: 5/16 inch
-
Estimate material needed:
- Add 10% extra for bends and waste: 1.8 × 1.1 = 1.98 meters
- Round up to 2.0 meters of each size
-
Construction time estimate:
- Cutting and deburring: 15 minutes
- Bending: 20 minutes
- Brazing joints: 25 minutes
- Total: approximately 60 minutes per student
In Tanzania, refrigerator and freezer repair is a common small business, especially in markets like Kariakoo in Dar es Salaam or along the main roads in Arusha. A technician who can construct proper refrigerant pipe circuits can service broken domestic freezers used by fish vendors to keep their catch fresh, or repair freezer boxes at local butcheries. This skill helps students start their own repair shops or gain employment at service centers, earning income in Tanzanian shillings while solving everyday cooling problems in their communities.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select materials, tools and equipment
- Draw mechanical working drawing (Detail and Assembly)
- Pipe the refrigerating components
- Mount electrical and perform wiring of the circuit
- Perform finishing to aesthetic appearance
- Perform spray painting
- Apply safety measures
- Commission the performance
- Clean the workplace, tools and equipment
- Store tools, equipment and machine
Tathmini ya matokeo
Designed and made freezer conform to technical specifications and aesthetic appearance
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Construct refrigerant pipe circuit
- Apply safety measures
Principles: The student should explain the principles of: (m) Heat transfer and exchange (n) Design parameters
Theories: The student should explain:
- Steps to estimate refrigerating capacity of a unit
- Materials science
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of tools, equipment and machines
- Environmental regulations
Swali
Which of the following is NOT one of the four main parts of a refrigerant pipe circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado