Mada za sehemu hiiDesigning and constructing small cold roomMada 6
Constructing Refrigerant Pipe Circuit
A refrigerant pipe circuit is the closed pathway through which the refrigerant circulates in a refrigeration system, connecting the compressor, condenser, evaporator, and other components. Constructing this circuit involves measuring, cutting, bending, joining, and installing pipes to ensure the system operates efficiently and safely.
The pipe circuit performs several essential functions in a refrigeration system:
- Transports refrigerant between components in a closed loop
- Maintains proper pressure throughout the system
- Enables heat transfer as the refrigerant changes state between liquid and gas
- Connects the high-pressure side (compressor to condenser) with the low-pressure side (evaporator to compressor)
A properly constructed pipe circuit ensures that the refrigerant flows in the correct direction and that the system achieves the desired cooling effect.
The following tools are essential for constructing a refrigerant pipe circuit:
- Measuring tape – for measuring pipe lengths accurately
- Drawing board, T-square, set squares, and protractors – for planning and marking pipe routes
- Pencils, eraser, and sharpener – for marking measurements
- Pipe cutter – for cutting copper pipes to size
- Flaring tool – for creating flare connections
- Bending springs or manual bender – for bending pipes without kinking
- Torque wrench – for tightening connections to the correct specification
Always wear safety goggles and gloves when cutting or bending pipes.
Step 1: Planning the Pipe Layout
Before cutting any pipe, draw a simple layout of the refrigeration system on paper. Identify:
- The location of each component (compressor, condenser, evaporator, expansion device)
- The required pipe lengths between components
- The path the pipes will follow, considering space and accessibility
This planning helps determine how much pipe is needed and where bends are required.
Step 2: Measuring and Marking
- Use a measuring tape to determine the exact distance between components.
- Add extra length for bends and fittings (typically 50–100 mm per bend).
- Mark the measured lengths clearly on the copper pipe using a pencil.
Step 3: Cutting the Pipe
- Use a pipe cutter to cut the copper pipe at the marked positions.
- Ensure the cut is square (perpendicular to the pipe's length) for proper fitting.
- Remove any burrs from the inside of the pipe using a reamer or deburring tool.
Step 4: Bending the Pipe
- Use a bending spring or manual bender to form bends at marked positions.
- Maintain a minimum bend radius to prevent kinking, which would restrict refrigerant flow.
- The rule of thumb is: bend radius should be at least 3 times the pipe diameter.
Step 5: Joining the Pipes
There are two common methods for joining refrigerant pipes:
- Flare fitting: Create a flare at the pipe end using a flaring tool, then connect with a flare nut.
- Soldered fitting: Clean the pipe ends, apply flux, and solder with silver or copper-phosphorus filler rod.
Ensure all joints are leak-free by checking with a leak detection solution.
Step 6: Installing the Complete Circuit
- Mount the components securely in their designated positions.
- Connect the pipes according to the planned layout, ensuring the high-pressure and low-pressure sides are correctly identified.
- Secure pipes with clamps to prevent vibration.
- Insulate suction (low-pressure) pipes to prevent heat gain from the surroundings.
A small cold room in Arusha requires a refrigerant pipe circuit connecting a compressor located 2.5 meters from the evaporator coil. The pipe route requires two 90° bends.
Calculate the total pipe length needed:
- Straight distance: 2.5 m
- Allowance for two bends (approximately 0.15 m each): 2 × 0.15 = 0.30 m
- Extra length for connections (approximately 0.1 m at each end): 2 × 0.1 = 0.20 m
Total pipe length = 2.5 + 0.30 + 0.20 = 3.00 m
A 3-meter length of copper pipe is required for the suction line between the evaporator and compressor.
- Always wear protective equipment when handling tools
- Ensure the work area is clean and free of flammable materials
- Check for refrigerant leaks after completing the installation
- Do not over-tighten connections, as this can damage the fitting or cause leaks
- Work in a well-ventilated area
- Using pipes that are too small, which causes pressure drops
- Failing to insulate suction pipes, leading to poor cooling performance
- Making sharp bends that restrict refrigerant flow
- Not checking for leaks after installation
- Improper soldering that creates blockages in the pipe
In Tanzania, the skills learned in constructing refrigerant pipe circuits are directly applied when servicing or repairing refrigerators in small workshops, such as those found in markets like Mlimani City in Dar es Salaam or along the roadside in Dodoma. A technician can use these skills to replace a faulty compressor or install a new evaporator in a domestic refrigerator, ensuring the system runs efficiently and consumes less electricity — which helps households save money on their Tanzania Electricity Supply Company (TANESCO) bills.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select proper tools and materials
- Produce working sketches
- Produce working drawings
- Take measurement of existing structure
- Choose required components
- Select refrigerant pipe size
- Clean workplace and tools
- Store tools and equipment
Tathmini ya matokeo
A set of working documents prepared conforms to set standards
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Size a cold room
- Calculate refrigeration load
Principles: The student should explain the principles of:
- Cooling of different types of refrigerants
- Primary and secondary refrigeration
- Heat transfer
Theories: The student should explain:
- Psychrometric diagrams
- Pressure enthalpy diagrams
- Pressure temperature charts
- Gas laws
- Working of flow control equipment
Circumstantial knowledge:
Detailed knowledge about:
- Working parameters of different refrigerants
- Electrical controls applied in refrigeration systems
- Mechanical and electrical installation requirement
- Building safety regulations
- Environmental regulations on greenhouse gases
- Imperial and SI units
- Mathematical calculation
Swali
Which tool is specifically used to cut copper pipes to the required size when constructing a refrigerant pipe circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado