Mada za sehemu hiiDesigning and constructing small cold roomMada 6
- Designing and drawing working drawing of small cold room
- Making cold room body
- Installing evaporator unit
- Constructing refrigerant pipe circuit
- Installing electrical wiring
- Charging with refrigerant and commissioning the system
Charging with Refrigerant and Commissioning the System
After designing and constructing a refrigeration system (such as a domestic refrigerator or small cold room), the system must be filled with the correct amount of refrigerant and tested to ensure it operates correctly. This two-step process is called charging and commissioning. Charging means introducing the proper amount of refrigerant into the system, while commissioning means testing, adjusting, and verifying that the system works efficiently and safely.
Purpose of Charging
Charging ensures the system contains the exact amount of refrigerant specified by the manufacturer. Too little refrigerant reduces cooling capacity, while too much refrigerant can damage the compressor and reduce efficiency.
Steps in Charging
-
Prepare the system
- Ensure the system is leak-free by performing a pressure test with nitrogen or dry air
- Connect the charging manifold and refrigerant cylinder
- Close all service valves except the one leading to the refrigerant cylinder
-
Evacuate the system
- Connect a vacuum pump to remove air and moisture
- Pull a vacuum to at least 500 microns (or as specified)
- Hold the vacuum for 15-30 minutes to ensure no leaks
-
Weigh the refrigerant charge
- Connect the refrigerant cylinder to the charging port
- Place the cylinder on a scale and record the initial weight
- Open the valve slowly to allow refrigerant to enter the system
- Monitor the scale and stop when the correct weight (as specified by the manufacturer) enters the system
-
Close valves and disconnect
- Close the service valves
- Remove the charging equipment carefully
- Check for leaks using a leak detector
Commissioning verifies that the system operates correctly after charging. It involves checking performance, making adjustments, and ensuring safety.
Steps in Commissioning
-
Start the compressor
- Turn on the power supply
- Start the compressor and allow it to run for 10-15 minutes
-
Check operating pressures
- Read the low-side pressure (evaporator pressure) on the manifold gauge
- Read the high-side pressure (condenser pressure) on the manifold gauge
- Compare readings with manufacturer's specifications for the refrigerant used
-
Check temperatures
- Measure the temperature at the evaporator inlet and outlet
- Measure the temperature at the condenser inlet and outlet
- Calculate superheat and subcooling values using the pressure-enthalpy chart
-
Adjust if necessary
- If superheat is too high, adjust the thermal expansion valve (TXV)
- If pressures are abnormal, check for blockages or refrigerant issues
-
Verify cooling performance
- Place a thermometer inside the refrigerated space
- Confirm the temperature reaches the desired set point
- Check that the compressor cycles on and off correctly
-
Document results
- Record all pressure and temperature readings
- Note any adjustments made
- Complete commissioning paperwork
- Always wear safety goggles and gloves when handling refrigerants
- Work in a well-ventilated area to avoid refrigerant vapor buildup
- Never overcharge the system — follow manufacturer specifications exactly
- Ensure electrical connections are secure before starting the system
- Keep a fire extinguisher nearby when working with refrigeration equipment
A small cold room in Arusha uses R-134a refrigerant. The manufacturer specifies a charge of 2.5 kg. During commissioning, the technician records the following readings:
- Low-side pressure: 150 kPa (at 5°C)
- High-side pressure: 900 kPa (at 45°C)
- Desired cold room temperature: 0°C
Commissioning check:
The technician compares the measured low-side pressure (150 kPa) with the pressure-enthalpy chart for R-134a. At 150 kPa, the saturation temperature is approximately 5°C. Since the cold room is at 0°C, there is a 5°C temperature difference across the evaporator, which is acceptable. The high-side pressure of 900 kPa corresponds to a condenser temperature of about 45°C, which is normal for ambient temperatures in Tanzania. The system is properly commissioned and operating within specifications.
In Tanzania, small cold rooms are commonly used by fish farmers and market vendors in cities like Mwanza and Dar es Salaam to preserve perishable goods. A technician who knows how to charge and commission a refrigeration system can start a small business offering installation and maintenance services for these cold rooms, earning income while helping reduce food spoilage in the local market.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select proper tools and materials
- Produce working drawings
- Take measurement of existing structure
- Choose required components
- Determine refrigerant load
- Choose correct refrigerant type to meet operating conditions
- Clean workplace and tools
- Store tools and equipment
Tathmini ya matokeo
A set of working documents prepared conforms to set standards
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Commission the system
- Calculate refrigeration load
Principles: The student should explain the principles of:
- Cooling of different types of refrigerants
- Primary and secondary refrigeration
- Heat transfer
Theories: The student should explain:
- Psychrometric diagrams
- Pressure enthalpy diagrams
- Pressure temperature charts
- Gas laws
- Working of flow control equipment
Circumstantial knowledge:
Detailed knowledge about:
- Working parameters of different refrigerants
- Electrical controls applied in refrigeration systems
- Mechanical and electrical installation requirement
- Building safety regulations
- Environmental regulations on greenhouse gases
- Imperial and SI units
- Mathematical calculation
Swali
What is the primary purpose of charging a refrigeration system with refrigerant?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado