Mada za sehemu hiiServicing cold roomsMada 6
Servicing Evaporator in Cold Rooms
The evaporator is a key component in refrigeration and air conditioning systems. It is the part where the refrigerant absorbs heat from the space being cooled, causing the liquid refrigerant to evaporate into a gas. In cold rooms, evaporators are mounted inside the insulated enclosure to remove heat from stored products like vegetables, fish, and meat. Regular servicing ensures the evaporator works efficiently and keeps the cold room at the correct temperature.
An evaporator consists of a coil with fins that allow refrigerant to absorb heat. When the refrigerant enters the evaporator as a low-pressure liquid, it evaporates by taking heat from the surrounding air. A fan blows air over the cold coils to distribute the cooled air throughout the cold room.
Main parts of an evaporator:
- Evaporator coil (copper tubes with aluminium fins)
- Fan or blower
- Drain pan (collects water from frost melt)
- Thermostat or temperature sensor
A poorly maintained evaporator can cause:
- Reduced cooling capacity
- Higher electricity consumption
- Ice buildup on the coils
- Food spoilage in cold rooms
- Complete system failure
Regular servicing keeps the evaporator clean, ensures proper airflow, and prevents refrigerant leaks.
The following tools and safety gear are required for servicing an evaporator:
- Electro mechanical tool kit (screwdrivers, wrenches, pliers)
- Bristle brush (for cleaning fins)
- Refrigerant leakage detector
- Gauge manifold
- Digital thermometer
- Pressure cleaner or water container
- Gloves
- Eye protection goggles
- Safety boots
- Cold room warm garments (working inside cold rooms is cold)
- Overall (protective clothing)
Before servicing, always observe these safety measures:
- Wear protective clothing — overall, gloves, safety boots, and eye protection at all times.
- Ensure power is isolated — switch off the refrigeration unit and disconnect the power supply before starting work.
- Use the leakage detector — check for refrigerant leaks before handling any components. Refrigerants can be harmful if inhaled.
- Work in pairs — never work alone inside a cold room.
- Warm clothing — cold rooms operate at low temperatures (below 0°C). Wear warm garments to prevent cold-related illness.
- Handle tools carefully — sharp edges on evaporator fins can cause cuts.
Step 1: Preparation and Inspection
- Switch off the cold room unit and disconnect power.
- Put on all protective clothing and gear.
- Inspect the evaporator visually for visible ice buildup, dirt, or corrosion.
- Use the refrigerant leakage detector to check for leaks around the coil joints and connections.
Step 2: Cleaning the Evaporator Coils
- Use a bristle brush to gently clean the aluminium fins. Brush in the direction of the fins to avoid bending them.
- For heavy dirt, use the pressure cleaner or spray water from a container to wash away debris.
- Ensure water does not enter the electrical motor housing.
Step 3: Cleaning the Fan and Blower
- Remove dust and debris from the fan blades using a brush or damp cloth.
- Check that the fan rotates freely without noise.
- Clean the fan guard if present.
Step 4: Checking the Drain Pan and Pipe
- Remove the drain pan and empty any water.
- Clear any blockages in the drain pipe using a flexible rod or brush.
- Ensure the drain pipe leads to a proper outlet.
Step 5: Inspecting and Testing Components
- Check all electrical connections for tightness and corrosion.
- Use the digital thermometer to measure the temperature difference between the air entering and leaving the evaporator. A difference of 8–12°C indicates proper operation.
- Connect the gauge manifold to check refrigerant pressure. Low suction pressure may indicate low refrigerant or a blocked evaporator.
Step 6: Final Checks and Restart
- Reconnect the power supply.
- Start the unit and observe the evaporator during operation.
- Ensure cold air is flowing evenly from the unit.
- Check that the thermostat maintains the desired temperature (e.g., 0°C to 4°C for a fresh produce cold room).
Step 7: Recording Service Details
- Write down the date of service, observations, and any replaced parts.
- Report any faults to the supervisor for further action.
A market vendor in Dodoma has a small cold room for storing fresh fish. The temperature inside rose to 8°C, and ice formed on the evaporator coils. A technician followed these servicing steps:
- Switched off the power and wore protective gear.
- Used a bristle brush to remove thick ice and dirt from the coils.
- Cleaned the fan blades and checked the drain pipe (it was blocked).
- Cleared the drain pipe and emptied the drain pan.
- Started the unit and used a digital thermometer — the air temperature difference was 10°C, confirming proper cooling.
After servicing, the cold room returned to 2°C, and the fish stayed fresh for three more days.
Servicing an evaporator involves cleaning the coils, fan, and drain system; checking for refrigerant leaks; inspecting electrical connections; and testing performance. Proper servicing maintains cooling efficiency, prevents food spoilage, and extends the life of the refrigeration system.
In Tanzania, cold rooms are commonly used at fish markets (like in Mwanza and Kigoma), butcheries, and small agro-processing businesses to preserve perishable goods. If a cold room at a local market stops cooling properly, a technician who knows how to service the evaporator can clean the coils, unblock the drain, and restore the temperature to keep fish, meat, and vegetables fresh — reducing losses for traders and ensuring food safety for families.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select tools and equipment
- Perform diagnostic trouble shooting
- Perform electrical checks
- Clean evaporator
- Inspect door sealing
- Check oil level in the engine and compressor
- Clean condensing unit
- Insulate refrigerant tubing
- Determine refrigerant level
- Perform pump down
- Charge refrigerant
- Clean workplace and tools
- Store tools and equipment
Tathmini ya matokeo
Demonstrate the ability of identify fault of evaporator and Service evaporator in cold rooms conforms to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure pressure quantities
- Interpret pressure and temperature relationship
Principles: The student should explain the principles of:
- Heat transfer
- Evaporator
Theories: The student should explain:
- Type of evaporator
Circumstantial knowledge:
Detailed knowledge about: Safe handling of evaporator and working tools
Swali
Which of the following is NOT a main part of an evaporator in a cold room?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado