Mada za sehemu hiiServicing chillersMada 5
A water supply system in refrigeration and air conditioning is a network of pipes, pumps, tanks, and valves that deliver water to and from a chiller unit. The water absorbs heat from the conditioned space and carries it to the chiller where it is cooled, then circulated back. This system is essential for cooling buildings, industrial processes, and refrigeration equipment.
In Tanzania, water-cooled chillers are commonly used in large buildings like hotels, hospitals, and factories. The water supply system includes the condenser water circuit and the chilled water circuit.
The main components that need servicing include:
- Suction and discharge pipes — carry water to and from the chiller
- Water pump — circulates water through the system
- Strainer — removes dirt and debris to protect equipment
- Expansion tank — accommodates water volume changes due to temperature
- Valves — control water flow and allow isolation of sections for maintenance
- Cooling tower — releases heat from the condenser water (in water-cooled systems)
1. Preparation and Safety
Before starting any servicing work, always put on your safety gear:
- Safety boots, overall, hand gloves, and safety goggles
- Ensure the chiller is switched off and locked out
- Allow the system to cool down to avoid burns
2. Visual Inspection
Check all visible components for:
- Corrosion or rust on pipes and fittings
- Water leaks at joints and connections
- Damaged insulation on pipes
- Physical damage to valves and strainers
3. Cleaning the Strainer
The strainer traps dirt and debris that could damage the pump and chiller tubes:
- Close the isolation valve before the strainer
- Open the strainer cover using appropriate plumbing tools
- Remove the screen and clean it with a hard brush and water
- Rinse thoroughly and check for holes or damage
- Reassemble with a new gasket if needed
- Open the valve slowly and check for leaks
4. Checking Water Quality and Level
Poor water quality causes scale, corrosion, and biological growth in the system:
- Check the water level in the expansion tank
- Test water pH and add water treatment chemicals as recommended
- Drain and refill the system if necessary, using clean water
5. Leak Detection
Leaks reduce system efficiency and can cause damage:
- Use a leak detector or soapy water solution on all joints
- Tighten loose fittings with a wrench
- If a pipe has a major leak, it may need patching or replacement using appropriate plumbing tools
6. Testing the Pump and Flow
After servicing, verify proper operation:
- Start the pump and check for unusual noises or vibrations
- Verify water flow at the outlet using a flow meter or observation
- Check pressure gauges to ensure normal operating pressure
A chiller's water pump is making a strange noise and the water flow is low. Upon inspection, you find the strainer is partially blocked with dirt and algae.
Solution:
- Isolate the strainer by closing the inlet valve
- Open the strainer housing and remove the screen
- Clean the screen with a hard brush and fresh water
- Rinse until all debris is removed
- Inspect the screen for holes — replace if damaged
- Reassemble the strainer with a proper gasket
- Open the valve slowly and check for leaks
- Restart the pump and confirm normal water flow and noise levels
This maintenance restored the water flow to normal and eliminated the pump noise.
- Always disconnect electrical power before working on the chiller
- Wear protective clothing and goggles when handling cleaning chemicals
- Use proper lifting techniques when moving heavy components
- Keep the work area clean and free of water to prevent slips
In Tanzania, hotels in Dar es Salaam and Arusha use water-cooled chiller systems for air conditioning. When guests complain that the rooms are not cooling properly, a maintenance technician would service the water supply system by cleaning strainers, checking pump operation, and testing water quality. Regular servicing keeps the chiller running efficiently, reduces electricity costs, and extends the life of the equipment — skills that are valuable for employment in building maintenance teams.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Select proper tools and equipment
- Perform trouble shooting in a logical sequence
- Measure water pressure temperature quantities
- Purge the system
- Perform plumbing works
- Clean tools equipment and workplace
- Store tools
Tathmini ya matokeo
Demonstrate the ability of identify fault of Service water supply system and Service water supply system in chiller conforms to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Regulate freezing temperature of secondary refrigerant
- Measure weights/volumes
Principles: The student should explain principle of:
- Heat transfer
- Change of state of matter
Theories: The student should explain:
- refrigerant
- Super heating
- Classification of Primary and secondary refrigerants
Circumstantial knowledge: Detailed knowledge of about:
- Safe handling of primary and secondary refrigerants Environmental regulations
Swali
Which component in the water supply system traps dirt and debris to protect the pump and chiller tubes?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado