Mada za sehemu hiiServicing chillersMada 5
- Servicing water supply system
- Servicing cooling tower
- Servicing fan coil unit
- Servicing/replacing refrigerant control units
- Servicing/charging with refrigerant
Refrigerant control units are essential components in refrigeration and air conditioning systems that regulate the flow of refrigerant between the high-pressure and low-pressure sides of the system. Proper servicing and replacement of these units is a critical skill for maintaining industrial chillers and ensuring system efficiency.
Thermostatic Expansion Valve (TXV)
The TXV is the most common refrigerant control device in modern air conditioning systems. It regulates refrigerant flow based on temperature sensing at the evaporator outlet, maintaining optimal superheat and ensuring efficient cooling.
Capillary Tube
A thin copper tube that restricts refrigerant flow, creating the pressure drop needed for evaporation. Capillary tubes are simple, inexpensive, and commonly found in smaller refrigeration systems.
Automatic Expansion Valve (AXV)
Maintains constant evaporator pressure by automatically adjusting the refrigerant flow, suitable for systems with varying cooling loads.
Service Valves
Manual valves used for charging, testing, and servicing the refrigeration system. They include gauge ports for connecting manifold gauges.
- Pressure reduction: Creates the pressure difference between condenser and evaporator
- Flow regulation: Controls the amount of refrigerant entering the evaporator
- Temperature control: Maintains proper superheat for efficient heat transfer
- System protection: Prevents liquid refrigerant from entering the compressor
Step 1: Safety Preparation
Before servicing any refrigerant control unit, ensure all safety gear is worn: safety goggles, hand gloves, safety boots, and overall. Verify the system is isolated and depressurized.
Step 2: Visual Inspection
Examine the control unit for visible damage, corrosion, or refrigerant leaks. Check connection points and mounting brackets for security.
Step 3: Performance Testing
Using the manifold gauge, measure high-side and low-side pressures. Compare readings with manufacturer specifications to identify abnormal operation.
Step 4: Leak Detection
Apply leak detector around all joints and connections. Any detected leaks require tightening or component replacement.
Step 5: Cleaning and Adjustment
Clean external surfaces and, for TXVs, verify proper superheat adjustment according to manufacturer specifications.
Step 1: Recovery
Recover refrigerant using approved recovery equipment following environmental regulations.
Step 2: Removal
Close service valves and disconnect electrical connections. Remove mounting hardware and carefully extract the control unit.
Step 3: Installation
Install the new control unit, ensuring proper orientation and connection torque. Use new gaskets and sealing washers as specified.
Step 4: Leak Testing
Perform leak test using leak detector after installation and before recharging.
Step 5: Recharging and Testing
Recharge system with correct refrigerant type and quantity. Run system and verify normal operating pressures and temperatures.
A chiller system shows low evaporator temperature and frost formation on the evaporator coil. Using the manifold gauge, the low-side pressure reads below normal at 2.1 bar (30 psi) instead of the required 4.8 bar (70 psi).
Diagnosis: The TXV may be undersized or incorrectly adjusted, allowing excess refrigerant flow.
Service action: Check and adjust TXV superheat setting. If adjustment does not correct the problem, replace the TXV with the correct size as specified by the manufacturer. After replacement, verify normal operating pressures of 4.5–5.0 bar (65–72 psi) on the low side.
| Fault | Possible Cause | Remedy |
|---|---|---|
| High low-side pressure | TXV stuck open | Adjust or replace TXV |
| Low low-side pressure | TXV stuck closed | Adjust, clean, or replace TXV |
| Intermittent cooling | Faulty thermal bulb | Check bulb placement and charge |
| Visible oil leaks | Damaged connections | Tighten or replace fittings |
- Always wear appropriate PPE when handling refrigerants and tools
- Use manifold gauge correctly to avoid system contamination
- Follow oxy-acetylene welding safety procedures when brazing components
- Never service systems without proper refrigerant recovery equipment
- Ensure adequate ventilation in the work area
In Tanzania, many commercial buildings in Dar es Salaam and other cities use central air conditioning chillers for climate control. When these systems develop faults such as insufficient cooling or high energy consumption, trained technicians must diagnose and service refrigerant control units like TXVs. A student who masters this skill can work as a refrigeration technician in hotels, hospitals, and food storage facilities, or start a small business repairing air conditioning systems for local shops and households.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Select proper tools and equipment
- Perform trouble shooting in a logical sequence
- Identify refrigerants used
- Measure pressure quantities
- Purge the system
- Select refrigerant
- Perform brazing
- Clean tools equipment and workplace
- Store tools
Tathmini ya matokeo
Demonstrate the ability of identify fault of refrigerant control units and Service refrigerant control units in chiller conforms to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Replace refrigerant control unit Measure pressure of refrigerant control unit
Principles: The student should explain principle of:
- Heat transfer
- Change of state of matter
Theories: The student should explain:
- Types of refrigerant control unit
- Classification of refrigerants
Circumstantial knowledge: Detailed knowledge of about:
- Safe handling of refrigerants Environmental regulations
Swali
What is the primary function of a thermostatic expansion valve (TXV) in a refrigeration system?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado