Mada za sehemu hiiServicing chillersMada 5
- Servicing water supply system
- Servicing cooling tower
- Servicing fan coil unit
- Servicing/replacing refrigerant control units
- Servicing/charging with refrigerant
Servicing and Charging Refrigerant in Chillers
Servicing and charging with refrigerant is the process of removing old or contaminated refrigerant from a refrigeration system, checking for leaks, repairing any faults, and then adding the correct amount of fresh refrigerant to restore the system to proper working condition. This is a critical maintenance activity for industrial air conditioning systems, particularly chillers that provide cooling for buildings, food storage, and commercial operations.
The main purposes of this procedure are:
- To restore cooling performance when the system has lost refrigerant
- To remove contaminated or degraded refrigerant that can damage system components
- To identify and repair refrigerant leaks
- To ensure the system operates efficiently and safely
- To extend the lifespan of the refrigeration equipment
The following tools and equipment are needed for safe and effective servicing:
Testing and detection equipment:
- Manifold gauge set (high and low pressure gauges)
- Leak detector
- Refrigerant identifiers
Recovery equipment:
- Refrigerant recovery unit
- Recovery cylinder for storing recovered refrigerant
Hand tools:
- Electromechanical toolbox (wrenches, screwdrivers, gauges)
- Oxy-acetylene welding set (for brazing repairs)
Safety gear:
- Safety goggles
- Hand gloves
- Safety boots
- Overall protective clothing
- Water bucket (for emergency washing)
Before starting any servicing work, always observe these important safety rules:
- Wear all required personal protective equipment (PPE)
- Ensure the work area is well-ventilated
- Never release refrigerant into the atmosphere — it must be recovered
- Keep flames and ignition sources away from refrigerant
- Check refrigerant type before charging — use the correct refrigerant as specified
- Work in pairs or ensure someone knows you are working with refrigerants
- Have the water bucket ready in case of refrigerant contact with skin or eyes
Step 1: Initial Assessment and Preparation
- Review the system's service history and identify the problem
- Ensure the chiller is switched off and disconnected from power
- Put on all safety equipment
- Position the recovery unit and connect hoses properly
Step 2: Refrigerant Recovery
- Connect the recovery unit to the system using proper hoses
- Activate the recovery unit to remove existing refrigerant from the system
- Transfer the recovered refrigerant into the recovery cylinder
- Verify that the system is empty using the manifold gauge
Step 3: Leak Detection
- Pressurize the system with nitrogen or dry air (never use oxygen)
- Use the leak detector to check all joints, connections, and components
- Mark any leak points found for repair
- Repair leaks using the oxy-acetylene welding set as needed
Step 4: Evacuation and Vacuum Testing
- Connect the vacuum pump to remove moisture and non-condensable gases
- Pull vacuum to the level specified by the manufacturer (typically below 500 microns)
- Hold the vacuum and monitor for pressure rise — indicates remaining moisture or leaks
- Maintain vacuum for the required time (usually 15-30 minutes)
Step 5: Charging with Fresh Refrigerant
- Identify the correct refrigerant type and amount required
- Connect the refrigerant cylinder to the system
- Add refrigerant slowly, monitoring pressure gauges
- For charging from the liquid side, invert the cylinder; for vapor charging, keep cylinder upright
- Charge to the correct amount as specified on the system nameplate
Step 6: Testing and Verification
- Start the system and observe normal operating pressures
- Check superheat and subcooling values if applicable
- Verify cooling performance is restored
- Check for any abnormal noises, vibrations, or leaks
- Document the work completed and refrigerant amount used
A small commercial chiller in a Dar es Salaam market loses its cooling capacity. The technician connects the manifold gauge and finds the low-side pressure is very low, indicating refrigerant loss. After recovering 2.5 kg of old refrigerant (which should have been 4.5 kg), a leak is detected at the evaporator coil connection. After repairing the leak and performing proper evacuation, the technician charges 4.5 kg of fresh R-134a refrigerant. The system now operates at correct pressures: low side at 2.5 bar and high side at 12 bar, restoring proper cooling for the market's cold storage.
- Always recover refrigerant never release it to the atmosphere
- The correct refrigerant type and charge quantity are critical — follow the nameplate
- Proper evacuation removes moisture that causes corrosion and system failure
- Always wear PPE when handling refrigerants
- Document all work for future maintenance reference
- Never overcharge or undercharge the system
In Tanzania, markets such as Kariakoo or Mwananyamala in Dar es Salaam have cold storage rooms and display chillers that keep perishable goods like fish, vegetables, and medicines fresh. When these chillers lose refrigerant and stop cooling, vendors lose money daily. A technician trained in servicing and charging can restore these systems, saving business owners from losing stock worth hundreds of thousands of shillings and helping to reduce food spoilage across the supply chain.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The students should be able to:
- Select proper tools and equipment
- Perform trouble shooting in a logical sequence
- Identify refrigerants used
- Measure pressure electrical and temperature quantities
- Purge the system
- /Refrigerant
- Perform brazing
- Perform plumbing works
- Clean tools equipment and workplace
- Store tools
Tathmini ya matokeo
Demonstrate the ability of identify properties of refrigerant and charge refrigerant in chiller conforms to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Identify freezing point of different refrigerant Measure amount of refrigerant gas
Principles: The student should explain principle of:
- Heat transfer
- Change of state of matter
Theories: The student should explain:
- Methods of charging
- Classification of refrigerants
Circumstantial knowledge: Detailed knowledge of about:
- Safe handling of refrigerants Environmental regulations
Swali
Which item of personal protective equipment (PPE) is NOT listed as required when servicing refrigerant in chillers?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado