Mada za sehemu hiiPerforming arc weldingMada 6
Welding Straight Beads
A straight bead is a continuous line of weld metal deposited along a straight line on a metal surface using an arc welding machine. It is the most basic weld bead pattern and serves as the foundation for all other welding techniques. When you strike an arc and move the electrode steadily in a straight line without weaving, you create a straight bead. The bead should have uniform width, height, and penetration along its entire length.
Straight beads are used in refrigeration and air conditioning work for:
- Joining metal pieces — Connecting two pieces of metal together by fusing them along a straight joint
- Building up material — Adding layers of weld metal to increase the thickness of a worn or damaged metal part
- Creating strong seams — Forming leak-tight joints in refrigerant pipes and containers
- Practice for beginners — Mastering straight beads helps students develop steady hands and consistent arc length before learning more complex techniques
Before welding straight beads, gather these tools and equipment:
- Welding machine (ARC welder)
- Welding cables with electrode holder
- Earth clamp (ground clamp)
- Welding shield (helmet or hand shield)
- Chipping hammer
- Wire brush
- Work bench with clamping facility
- Welding tongs (heat-resistant pliers)
- Angle grinder
- Flat file
- Bench vice
- Scriber
- Centre punch
- Ball pein hammer
Always wear the following safety gear when performing arc welding:
- Overalls (welding coveralls)
- Leather gloves
- Canvas spats (leg protection)
- Safety boots (steel-toe boots)
- Leather apron
- Welding helmet with proper shade lens
Safety First: Arc welding produces intense ultraviolet light, sparks, and fumes. Never look at the arc without protection, and always work in a well-ventilated area.
-
Clean the metal surface — Use the wire brush, angle grinder, or file to remove rust, paint, oil, grease, and dirt from the area to be welded. A clean surface ensures proper penetration and a strong weld.
-
Secure the workpiece — Clamp the metal piece firmly on the work bench using the bench vice or clamps. Make sure it is stable and will not move during welding.
-
Set the welding machine — Select the correct current (amperage) for the electrode size and metal thickness. For mild steel plate of 3mm thickness, use a 10-12 SWG (Standard Wire Gauge) electrode at approximately 50-60 amps.
-
Prepare the electrode — Inspect the electrode for damage. Ensure it is dry; a damp electrode causes porosity in the weld. Insert the electrode into the holder and tighten securely.
-
Connect the earth clamp — Attach the earth clamp directly to the workpiece as close as possible to the welding area. Ensure good electrical contact.
Step 1: Striking the Arc
- Position your body comfortably with your leading hand holding the electrode holder and your trailing hand supporting it or holding the welding shield
- Bring the electrode tip to the metal surface at about 70-80 degrees angle
- Gently scratch the electrode across the metal while moving forward — this action creates the arc
- Once the arc is established, maintain a consistent arc length of approximately 2-3mm (about the thickness of a matchstick)
Step 2: Maintaining the Arc Length
- Keep the arc length constant throughout the bead — too short causes sticking, too long produces an unstable arc and spatter
- The arc should produce a steady, humming sound
- Watch the weld pool (the molten metal at the arc point) to judge your distance
Step 3: Moving the Electrode
- Move the electrode steadily along the intended straight line
- Maintain a consistent travel speed — moving too fast produces a thin, weak bead; moving too slow creates a bulky, irregular bead
- Keep the electrode angle constant (approximately 70-80 degrees from the workpiece surface)
- Do not weave or oscillate — this is a straight bead, not a weave bead
Step 4: Creating a Uniform Bead
A good straight bead should show:
- Uniform width — The bead should be the same width from start to finish
- Even height — The bead should not be too high or too low in any section
- Regular ripple pattern — The surface should show even, closely-spaced ripples
- Good penetration — The weld must fuse properly with the base metal at the edges
- No defects — No cracks, porosity holes, or spatter marks
Step 5: Completing the Weld
- Lift the electrode to break the arc when you reach the end of the intended bead
- Allow the weld to cool naturally — do not quench with water
- Use the chipping hammer to remove slag from the weld
- Clean the bead thoroughly with the wire brush
- Inspect your work against the quality criteria above
A student welded a straight bead on a 3mm mild steel plate using a 3.2mm electrode at 55 amps. After cleaning the slag, the student observed the following:
- Bead length: 100mm
- Bead width: 8mm (uniform along the whole length)
- Bead height: 2mm
- Penetration: The weld fused completely at both edges with no gaps
- Surface: Even ripple pattern, no cracks visible
Evaluation: This is a good quality straight bead because it has uniform width, consistent height, full penetration, and a regular surface appearance.
| Problem | Cause | Solution |
|---|---|---|
| Uneven bead width | Inconsistent travel speed | Practice maintaining steady hand movement |
| Excessive spatter | Arc length too long | Keep arc length at 2-3mm |
| Poor penetration | Current too low or dirty metal | Increase amperage or clean surface better |
| Slag inclusions | Incomplete slag removal | Clean slag thoroughly between passes |
| Cracks in bead | Rapid cooling or high stress | Allow slower cooling, preheat if needed |
- Practice striking the arc first on scrap metal before welding the actual piece
- Start with short beads (30-40mm) and gradually increase length as your hand steadies
- Focus on maintaining constant travel speed and arc length
- Always check your PPE before starting any welding task
- Work in pairs or groups as directed by your instructor, taking turns to weld and observe
In Tanzania, refrigeration and air conditioning technicians commonly use straight bead welding when repairing leaking copper or steel pipes in air conditioners and refrigerators. For example, if a freezer at a market stall in Dar es Salaam develops a leak in the refrigerant tubing, a technician would use arc welding with straight beads to braze or weld a patch onto the damaged section, restoring the appliance to working condition without needing to replace the entire unit — saving the business owner hundreds of thousands of Tanzanian shillings in repair costs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Inspect the machine, cable and electrode holder
- Interpret working drawing
- Prepare materials for welding
- Select type and size of electrode for the job
- Set recommended current
- Weld a work piece
- Maintain electrode angle and arc length
- Control electrode travel speed along the joint
- Chip off metal slag and wire brush
- Inspect for weld defect
- Clean workplace
- Clean tools and equipment
- Store tools and equipment in safe place
Tathmini ya matokeo
Welded metal conforms to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain the welding technique used
Principles: The student should explain the principles of:
- Arc welding
- Minimizing distortion
- Obtaining good penetration
- Selecting weld current
Theories: The student should explain:
- Types of metals and their properties
- Types and functions of welding equipment
- Groove preparations
- Uses of wire brush and chipping hammer
- Metallurgical effects on weldment
- Characteristics of AC and DC welding machine
- Types of welds
- Types of electrode coatings and function
- Work angle and lead angle
- Welding symbols
- Types of distortion
- Joint design
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while welding work piece
- First Aid
Swali
What is the primary purpose of a straight bead in arc welding?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado