Mada za sehemu hiiPerforming arc weldingMada 6
Down Hand Tee Joint Welding in Arc Welding
Down hand tee joint welding is a fundamental arc welding technique where a horizontal plate (the web) is joined to a vertical plate (the flange) in a T-shape configuration, with the welder working in the "down hand" position—meaning the welding direction is from left to right (or right to left) along the joint, and the weld pool flows downward due to gravity. This joint configuration is commonly used in refrigeration and air conditioning work to join metal components such as ductwork, support brackets, and casing panels.
- Tee joint: A joint formed by two members perpendicular to each other, forming a "T" shape
- Down hand position: The welding position where the weld is made in a horizontal plane while the welder moves along the joint in a horizontal direction
- Root gap: The distance between the two workpieces at the root of the joint before welding
- Run-off tab: A short piece of metal attached to the end of a joint to allow the weld to run off properly
- Fillet weld: A weld that joins two surfaces at right angles, typically triangular in cross-section
Before starting, ensure the following tools and safety gear are available:
- Welding machine with suitable current setting
- Welding cables (electrode holder and earth clamp)
- Mild steel electrodes (E6013 or E7018, typically 3.2mm diameter for general work)
- Welding shield (helmet or hand shield)
- Chipping hammer and wire brush
- Welding tongs (for handling hot workpieces)
- Angle grinder and flat file for preparation
- Bench vice and scriber for marking
- Centre punch for marking layout
- Ball pein hammer for shaping
Personal Protective Equipment (PPE)
- Overalls (full body coverage)
- Leather gloves
- Canvas spats (leg protection)
- Safety boots (steel-toed)
- Leather apron
- Welding helmet with appropriate shade lens
Step 1: Preparation and Layout
- Clean the metal surfaces to be joined using a wire brush or angle grinder to remove rust, paint, oil, and scale
- Use a scriber and rule to mark the position of the vertical plate on the horizontal plate
- Set the vertical plate at 90° to the horizontal plate, ensuring proper fit-up
- Clamp the workpieces securely in the bench vice or use jigs to hold them in position
- Check and maintain the root gap (typically 1.5mm to 2mm for mild steel plate)
Step 2: Setting the Welding Machine
- Connect the earth clamp to the workbench or workpiece
- Select the appropriate electrode (E6013 is suitable for beginners due to its easy arc striking)
- Set the welding current according to electrode diameter:
- For 3.2mm electrode: 100–120 amperes
- Adjust based on metal thickness and joint fit-up
Step 3: Striking the Arc and Running the Weld
- Hold the electrode at an angle of 60–70° from the vertical
- Strike the arc by scraping the electrode tip across the workpiece
- Establish a small weld pool at the start of the joint
- Maintain a consistent arc length (approximately equal to electrode diameter)
- Move the electrode in a straight line along the joint, keeping the weld pool small and controlled
- Use a triangular or "U" weave pattern for wider welds
- Run off the weld onto a run-off tab at the end of the joint to avoid craters
Step 4: Finishing the Weld
- Allow the weld to cool naturally—do not quench with water
- Use the chipping hammer to remove slag from the weld bead
- Clean the weld seam thoroughly with a wire brush
- Inspect the weld for uniformity, penetration, and defects
A student is required to weld a tee joint using a 3.2mm E6013 electrode on 6mm thick mild steel plates.
Solution:
- Current setting: 110 A (mid-range for 3.2mm electrode)
- Electrode angle: 65° from vertical
- Arc length: approximately 3mm
- Travel speed: steady, maintaining a weld bead width of 6–8mm
- Weave pattern: small triangular motion for consistent fillet formation
The completed weld should show:
- Uniform bead appearance
- Complete fusion at the root
- Fillet legs of approximately equal size (about 5mm each side)
- No porosity, cracks, or excessive spatter
- Porosity (gas holes): Caused by damp electrodes or contaminated metal—always store electrodes in a dry place and clean workpieces
- Incomplete penetration: Root gap too small or current too low—ensure adequate root gap and correct current setting
- Excessive spatter: Current too high or arc length too long—reduce current and maintain proper arc length
- Uneven bead: Inconsistent travel speed—practice maintaining steady hand movement
- Always inspect cables for damage before use
- Ensure the work area is free from flammable materials
- Never look at the arc without proper eye protection
- Keep the welding helmet in good condition with the correct shade lens (usually shade 10–12)
- Use welding tongs to handle hot workpieces—never use bare hands
- Ensure proper ventilation to remove welding fumes
- Secure loose clothing and tie back long hair
In Tanzania, down hand tee joint welding is applied when fabricating and repairing refrigeration display cabinets, air conditioning ductwork, and cold room panels found in markets like Kariakoo in Dar es Salaam or in small workshop garages in Arusha. A refrigeration technician repairing a split air conditioning unit may need to weld a broken mounting bracket using this technique, ensuring the unit is securely reattached to the wall—preventing vibrations and extending the equipment's service life while saving the owner the cost of purchasing a new unit, which could cost over TSh 500,000.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Inspect the machine, cable and electrode holder
- Interpret working drawing
- Prepare materials for welding
- Select type and size of electrode for the job
- Set recommended current
- Weld a work piece
- Maintain electrode angle and arc length
- Control electrode travel speed along the joint
- Chip off metal slag and wire brush
- Inspect for weld defect
- Clean workplace
- Clean tools and equipment
- Store tools and equipment in safe place
Tathmini ya matokeo
Welded metal conforms to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain the welding technique used
Principles: The student should explain the principles of:
- Arc welding
- Minimizing distortion
- Obtaining good penetration
- Selecting weld current
Theories: The student should explain:
- Types of metals and their properties
- Types and functions of welding equipment
- Groove preparations
- Uses of wire brush and chipping hammer
- Metallurgical effects on weldment
- Characteristics of AC and DC welding machine
- Types of welds
- Types of electrode coatings and function
- Work angle and lead angle
- Welding symbols
- Types of distortion
- Joint design
Circumstantial knowledge:
Detailed knowledge about:
- Safety precautions to be observed while welding work piece
- First Aid
Swali
What is the recommended root gap for mild steel plates when welding a down hand tee joint?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado