Mada za sehemu hiiPerforming resistance weldingMada 2
- Joining steel plates
- Joining steel pipes
Joining steel plates using resistance welding is a common skill in refrigeration and air conditioning work where metal components must be securely fastened without using bolts or rivets. This method uses heat generated by electrical resistance to melt and fuse metal surfaces together.
Resistance welding is a welding process that joins metals by applying heat from the resistance to electric current flow between two electrodes that clamp the metal pieces together. The heat generated at the contact points causes the metals to melt and fuse when pressure is maintained.
The most common type used for joining steel plates is spot welding, where heat is concentrated at specific points where the electrodes press against the metal. This creates strong, localized welds without heating the entire piece.
1. Preparation
- Select two steel plates of appropriate thickness (usually 0.5 mm to 3 mm)
- Clean the surfaces to be joined using a wire brush to remove rust, paint, or dirt
- Cut the plates to the required dimensions using tin snips if necessary
2. Positioning the Plates
- Place the two steel plates together in the position where they need to be joined
- Ensure the edges are properly aligned and flush
3. Setting Up the Equipment
- Turn on the resistance welding machine
- Adjust the welding current and pressure according to the thickness of the plates
- Thicker plates require higher current and more pressure
4. Performing the Weld
- Position the electrodes of the welding machine on either side of the plates at the joint point
- Apply firm pressure to hold the plates in place
- Activate the welding cycle (the current flows through the electrodes)
- Hold the pressure for a few seconds after the welding cycle completes to allow the weld to cool and solidify
5. Inspection
- Check the weld joint for proper fusion
- The weld should appear as a small circular spot on both sides of the plates
- Ensure the plates are securely joined without gaps
- Always wear welding apron and hand gloves when operating the machine
- Use welding shield to protect eyes from the bright light produced during welding
- Wear safety boots to protect feet from falling objects
- Use tongs to handle hot metal pieces after welding
- Ensure the work area is free from flammable materials
A refrigerator service technician needs to join a 1 mm thick steel plate to another plate to repair a cabinet panel. Using a resistance welding machine set at 50 amperes with medium electrode pressure, the technician places the plates together, activates the weld for 0.5 seconds, and creates a strong spot weld. The resulting joint can withstand the normal handling and vibration encountered in refrigerator operation.
| Fault | Possible Cause | Remedy |
|---|---|---|
| Weak weld | Low current or short welding time | Increase current or extend welding time |
| Burn through | Excessive current or too long welding time | Reduce current or shorten welding time |
| Porous weld | Dirty surfaces or insufficient pressure | Clean surfaces and increase electrode pressure |
In Tanzania, refrigeration and air conditioning technicians frequently use resistance welding to repair commercial cold rooms at markets like Mwanza or Dodoma, where metal panels need quick and strong joining without bulky fasteners. A technician can efficiently patch a damaged refrigeration unit panel by spot welding a new steel plate, restoring the unit to service and helping vendors preserve perishable goods such as fish and vegetables.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Mark the two pieces
- Perform spot welding to join two flat metal pieces
- Hold the work pieces together using a grip plier
- Set proper current
- Radius gauge
- Store tools and equipment
- Clean workplace
Tathmini ya matokeo
A set of work pieces joined conform to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Prepare work piece
- Perform spot welding
- Set current
Principles: The student should explain the principles of:
- Resistance welding
- Spot welding
Theories: The student should explain:
- Importance of cleaning the joint area before joining
- Resistance welding
- Current settings for different sheet thicknesses
- Safe handling of work pieces
- Safe handling of working tools
- Safe handling of measuring instruments
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of work pieces
Swali
What type of resistance welding is most commonly used for joining steel plates in refrigeration and air conditioning work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado