Mada za sehemu hiiPerforming resistance weldingMada 2
- Joining steel plates
- Joining steel pipes
Joining Steel Pipes Using Resistance Welding
Resistance welding is a method of joining steel pipes by applying heat generated from electrical resistance. In refrigeration and air conditioning work, steel pipes are used to carry refrigerants, and they must be joined securely to prevent leaks. This technique is fast, economical, and produces strong joints without needing additional filler materials.
Resistance welding is preferred in refrigeration and air conditioning because:
- It creates leak-proof joints essential for containing refrigerants
- The process is quick and suitable for workshop conditions
- No additional welding rods or gases are required
- It produces clean joints with minimal distortion
Before starting, gather these tools:
- Resistance welding machine (spot welder)
- Tongs (for handling hot materials safely)
- Welding apron and hand gloves
- Welding shield (face protection)
- Safety boots
- Tin snip (for cutting pipe sections)
- Wire brush (for cleaning pipe surfaces)
- Power supply (appropriate voltage for the machine)
Always observe these safety measures:
- Wear protective clothing before starting any welding work
- Keep the welding area free from flammable materials
- Use tongs to handle hot pipes — never use bare hands
- Ensure the welding shield is in position before energizing the machine
- Check that the work area is well-ventilated
- Disconnect power when changing electrodes or adjusting the machine
Step 1: Prepare the Pipes
- Cut the steel pipes to the required lengths using tin snips
- Remove any burrs or sharp edges from the cut ends
- Clean the mating surfaces thoroughly with a wire brush to remove rust, oil, or dirt
- Ensure the pipe ends are properly aligned and fit together snugly
Step 2: Position the Pipes
- Place the prepared pipes in the welding fixture or clamp them securely
- Align the joints properly so that the pipe ends overlap or butt against each other correctly
- Maintain proper alignment throughout the welding process
Step 3: Set Up the Resistance Welding Machine
- Select appropriate electrode size for the pipe diameter
- Adjust the welding current and timing according to manufacturer specifications
- Ensure electrodes are clean and properly positioned
Step 4: Perform the Weld
- Bring the electrodes into contact with the pipe surfaces on either side of the joint
- Activate the welding cycle (press the control switch)
- Hold the pipes steady while the welding current flows through the resistance point
- The heat generated at the contact points melts and fuses the metal together
Step 5: Inspect and Finish
- Allow the joint to cool naturally — do not quench with water
- Inspect the weld for uniformity and soundness
- Remove any excess material or rough edges with a file if necessary
- Clean the completed joint before installing in the system
A refrigerator service technician needs to join two sections of copper-coated steel pipe that will carry refrigerant from the compressor to the condenser. The pipe diameter is 6 mm, and the technician uses a resistance spot welder set at 15 amperes for 0.3 seconds.
The technician:
- Cuts both pipe sections to length using tin snips
- Cleans the ends with a wire brush to remove oxidation
- Aligns the pipe ends and clamps them in position
- Applies the welding current — the resistance at the joint heats the metal to fusion temperature
- Allows the joint to cool and checks for a uniform weld nugget
The resulting joint is strong enough to withstand the pressure in the refrigerant system and will not leak during operation.
| Defect | Cause | Prevention |
|---|---|---|
| Weak joint | Insufficient current or time | Increase welding parameters appropriately |
| Burn-through | Excessive current or time | Reduce welding parameters |
| Poor alignment | Improper clamping | Secure pipes firmly before welding |
| Porosity | Dirty or contaminated surfaces | Clean pipe surfaces thoroughly before welding |
In Tanzania, refrigeration and air conditioning technicians use resistance welding when installing or repairing split air conditioners in homes, shops, and offices. For example, when a breakdown causes a refrigerant leak in the piping between the indoor and outdoor units, a technician in Dar es Salaam would use resistance welding to join new steel pipe sections, ensuring the system regains its leak-free operation and the customer can use their air conditioner again during hot seasons.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Mark the two pieces
- Perform spot welding to join two flat metal pieces
- Hold the work pieces together using a grip plier
- Set proper current
- Radius gauge
- Store tools and equipment
- Clean workplace
Tathmini ya matokeo
A set of work pieces joined conform to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Prepare work piece
- Perform spot welding
- Set current
Principles: The student should explain the principles of:
- Resistance welding
- Spot welding
Theories: The student should explain:
- Importance of cleaning the joint area before joining
- Resistance welding
- Current settings for different sheet thicknesses
- Safe handling of work pieces
- Safe handling of working tools
- Safe handling of measuring instruments
Circumstantial knowledge:
Detailed knowledge about:
- Safe handling of work pieces
- Safe handling of working tools
- Safe handling of measuring instruments
Swali
According to the source material, why is resistance welding preferred in refrigeration and air conditioning work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado