Mada za sehemu hiiPerforming aluminium weldingMada 2
- Joining aluminium sheets
- Joining aluminium tubes
Aluminium sheets are thin, flat pieces of aluminium metal used in refrigeration and air conditioning equipment such as evaporators, condensers, and ductwork. Joining aluminium sheets is a skilled task that requires proper preparation, the right tools, and safety precautions because aluminium oxidises quickly and conducts heat rapidly.
Aluminium sheets are flat aluminium products typically ranging from 0.5 mm to 6 mm in thickness. In refrigeration and air conditioning, they are used to fabricate components that require lightweight, corrosion-resistant materials. Unlike steel, aluminium forms a protective oxide layer on its surface immediately when exposed to air, which must be removed before joining to ensure a strong weld.
Before joining aluminium sheets, gather the following tools and equipment:
- TIG (Tungsten Inert Gas) welding machine
- Wire brush (stainless steel, used only for aluminium)
- Clamps and jigs to hold sheets in position
- Cleaning rags and acetone for degreasing
- Filler rod (aluminium alloy suitable for welding)
- Protective safety gear
Always wear the following protective equipment when joining aluminium sheets:
- Safety boots to protect feet from falling objects and hot materials
- Welding hand gloves to protect hands from heat and sparks
- Welding apron to protect clothing from burns
- Head fixed welding shield to protect eyes and face from intense light
Step 1: Define and Select the Sheets
Identify the aluminium sheets to be joined based on the thickness and application. For refrigeration work, typically 1 mm to 2 mm sheets are used for ductwork and small components.
Step 2: Prepare the Sheets
- Clean the aluminium sheets using acetone to remove grease, oil, and dirt.
- Use a stainless steel wire brush to remove the oxide layer from the surfaces to be joined and the surrounding area.
- Clamp the sheets in position using jigs or clamps, ensuring they are properly aligned with no gaps larger than the sheet thickness.
Step 3: Set Up the TIG Machine
- Select the appropriate tungsten electrode (typically 2% lanthanated or ceriated).
- Set the correct amperage based on sheet thickness (approximately 1 amp per 0.1 mm of thickness).
- Use pure argon gas as the shielding gas at a flow rate of 15-20 litres per minute.
Step 4: Weld the Joint
- Strike an arc and create a weld pool on the joint.
- Add filler rod gradually to build up the weld bead.
- Maintain a consistent travel speed to produce a uniform weld.
- Allow the joint to cool slowly to avoid cracking.
Step 5: Inspect the Weld
- Check the weld for defects such as porosity, cracks, or incomplete fusion.
- Clean the weld area to remove any spatter or oxide residue.
A technician needs to join two aluminium sheets, each 1.5 mm thick, to fabricate a small duct section for an air conditioning system. The sheets are cleaned and clamped together.
Calculation for welding current:
- Rule of thumb: 1 amp per 0.1 mm of thickness
- Thickness = 1.5 mm
- Required current = 1.5 ÷ 0.1 = 15 amps per mm = approximately 15-20 amps
The technician sets the TIG machine to 18 amps, uses argon shielding gas at 18 L/min, and successfully produces a sound weld joint suitable for the ductwork.
- Porosity (gas holes): Caused by contamination or insufficient shielding gas. Ensure proper cleaning and adequate gas flow.
- Cracking: Caused by rapid cooling or incorrect filler rod. Use proper filler alloy and allow slow cooling.
- Incomplete fusion: Caused by insufficient heat or poor joint preparation. Ensure adequate amperage and clean surfaces properly.
In Tanzania, refrigeration and air conditioning technicians in Dar es Salaam, Arusha, and other cities often repair and fabricate evaporator coils and ductwork using aluminium sheets. A local technician might join aluminium sheets to repair a split air conditioning duct in a shop, using TIG welding to create a durable, leak-free joint that restores cooling efficiency for the customer's comfort.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Set correct welding parameters
- Perform sheet joints
- Perform tube joint
- Perform butt welding
- Perform overhead welding
- Clean tools and workplace
- Store tools and equipment
- Perform left and right welding
Tathmini ya matokeo
A set of work pieces welded conform to specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Set correct gas pressure
- Set correct current
Principles: The student should explain the principles of metal fusion
Theories: The student should explain:
- Oxide formation problems with aluminium welding
- Different welding processes
Circumstantial knowledge:
Detailed knowledge about:
- Work safety and health regulation
- Properties of engineering materials
Swali
What does the head fixed welding shield protect during TIG welding of aluminium sheets?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado