Mada za sehemu hiiInstalling chilling plantsMada 7
Installing Electric Control Circuit in Refrigeration and Air Conditioning
An electric control circuit is a system of electrical components that automatically controls the operation of refrigeration and air conditioning equipment, ensuring safe starting, running, and stopping of compressors, fans, and other motors based on temperature and pressure conditions.
Electric control circuits in refrigeration and air conditioning serve three main purposes:
- Starting and stopping — Automatically turn the compressor on when cooling is needed and off when the desired temperature is reached
- Protection — Protect the motor and compressor from damage due to abnormal conditions like high pressure, low pressure, or overload
- Sequence of operation — Ensure that components operate in the correct order (e.g., condenser fan must run before the compressor)
1. Thermostat
A temperature-sensing device that opens or closes electrical contacts based on temperature changes. In refrigeration, it controls the compressor based on evaporator temperature.
2. Pressure Controls
- High-pressure control — Protects against excessively high discharge pressure by stopping the compressor
- Low-pressure control — Protects against low suction pressure that could damage the compressor
3. Motor Starter and Overload Protection
The motor starter engages the compressor motor, while overload protection guards against excessive current that could overheat the motor windings.
4. Contactor
An electrically operated switch that allows the low-voltage control circuit to switch the high-voltage motor circuit on and off.
5. Capacitors
Provide starting torque for single-phase motors commonly used in small refrigeration and AC units.
6. Relay
A switch that uses a small current to control a larger current, commonly used for fan motors and compressor starting circuits.
- Multimeter (for measuring voltage, current, and continuity)
- Screwdrivers (flathead and Phillips)
- Pliers and wire strippers
- Wire connectors and electrical tape
- Circuit diagram/schematic
- Spirit level (for mounting components)
- Safety apparels (insulated gloves, safety goggles)
- Always disconnect power supply before working on any electrical circuit
- Use properly insulated tools
- Ensure hands are dry when working with electricity
- Follow lockout/tagout procedures
- Never work on live circuits
- Use appropriate personal protective equipment (PPE)
Step 1: Study the Circuit Diagram
Read and understand the wiring schematic. Identify all components, their symbols, and the connection points. The diagram shows how each component connects and the sequence of operation.
Step 2: Gather Tools and Materials
Collect all required tools, wires, connectors, and components specified in the diagram. Check that all components are the correct rating and type for the system.
Step 3: Prepare the Installation Area
Mount the control panel or junction box in a suitable location, usually near the equipment. Ensure the area is clean, dry, and accessible for maintenance.
Step 4: Install Control Components
Mount the thermostat, pressure controls, and other sensing devices in their designated positions. Use the spirit level to ensure proper alignment.
Step 5: Run and Connect Wiring
Run the wiring between components according to the circuit diagram. Use appropriate wire sizes for the current ratings. Strip wire ends cleanly and use proper connectors.
Step 6: Ground the System
Connect all grounding wires properly to ensure safety and compliance with electrical standards.
Step 7: Check All Connections
Verify every connection is secure and correctly positioned. Use a multimeter to check for continuity and ensure no short circuits exist.
Step 8: Test the Circuit
Restore power and test the control circuit operation. Verify that:
- The compressor starts and stops according to thermostat settings
- Pressure controls trip at correct pressures
- All safety devices function properly
A small walk-in cold room uses a single-phase compressor motor rated at 2.5 kW. The system has a room thermostat, low-pressure control, high-pressure control, and a magnetic contactor.
Circuit sequence:
- Power supply (230V) enters the control circuit
- Thermostat contacts close when room temperature rises above set point
- Low-pressure control (LPC) and high-pressure control (HPC) must be in normal (closed) position
- When all safety controls are satisfied, current flows to the coil of the magnetic contactor
- The contactor closes, supplying 230V to the compressor motor
- When temperature drops, thermostat opens and de-energizes the contactor, stopping the compressor
Wiring connections:
- Line (L) from power supply → thermostat → LPC → HPC → contactor coil → Neutral (N)
- Contact terminals of contactor → compressor motor → overload protection → N
| Fault | Possible Cause | Correction |
|---|---|---|
| Compressor does not start | Thermostat not calling for cooling | Check thermostat setting |
| Compressor trips on high pressure | Condenser dirty or fan failed | Clean condenser, check fan |
| Intermittent operation | Loose connection | Tighten all wire connections |
| Overload trips frequently | Low refrigerant, dirty filter | Check refrigerant charge, clean filter |
In Tanzania, technicians working in fish processing plants along Lake Victoria or in butcheries in Dar es Salaam regularly install and maintain electric control circuits in cold rooms. When a restaurant in Mwanza needs a new refrigeration system, the technician must correctly install the control circuit so that the cold room maintains fish at the required -18°C while automatically cycling the compressor on and off to save electricity costs, which is crucial for small businesses operating on tight budgets in areas where power supply can be unreliable.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Read installation drawings
- Prepare machine foundations
- Perform grouting
- Perform machinery alignment for belt driven components
- Build piping circuit
- Use safely lifting tackles
- Fabricate simple items as per on site requirements
- Measure and record required operation parameters
- Clean workplace tools and equipment
- Store tools and equipment
Tathmini ya matokeo
The chilling plant installed and documentation conform to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Perform machinery alignment
- Anchor equipment
Principles: The student should explain the principles of:
- Heat transfer
- Air flow in ducts / pipes
Theories: The student should explain:
- Super heating and sub-cooling
- Refrigeration cycle
- Storage temperature requirements of different commodities
- Classification of refrigerants
Circumstantial knowledge:
Detailed knowledge about:
- Construction site safety management Environmental regulations
Swali
What are the three main purposes of electric control circuits in refrigeration and air conditioning systems?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado