Mada za sehemu hiiInstalling chilling plantsMada 7
- Installing condensing unit
- Installing indoor unit
- Installing cooling tower
- Installing piping circuit
- Installing electrical supply circuit
- Installing electric control circuit
- Charging with refrigerant and commissioning the system
Charging with Refrigerant and Commissioning the System
Charging a refrigeration or air conditioning system means adding the correct amount of refrigerant into the system after it has been installed or serviced. Commissioning means testing and adjusting the system to make sure it works properly, cools effectively, and runs safely. Both processes are essential before any refrigeration or AC unit can be used.
A refrigeration system needs the exact amount of refrigerant to work efficiently. Too little refrigerant (undercharge) causes poor cooling and high energy use. Too much refrigerant (overcharge) can damage the compressor and reduce cooling performance. After charging, commissioning verifies that the system operates within the manufacturer's specifications.
Before starting any charging or commissioning work, always follow these safety rules:
- Wear safety gloves, goggles, and protective clothing at all times
- Work in a well-ventilated area to avoid breathing refrigerant vapors
- Never release refrigerant into the atmosphere — it harms the environment
- Ensure the system is powered off before connecting or disconnecting gauges
- Keep fire and sparks away from the work area
The following tools are required for charging and commissioning:
- Refrigerant cylinder (with the correct refrigerant type)
- Charging hose with manifold gauge set
- System analyzer (to measure temperature and pressure)
- Multimeter (for electrical checks)
- Thermometer
- Vacuum pump (to remove moisture before charging)
- Spirit level (to ensure unit is level)
- Screwdrivers, wrenches, and other hand tools
Step 1: Prepare the System
Before adding refrigerant, the system must be clean and dry. Connect a vacuum pump to the system and run it for at least 30 minutes to remove air and moisture. This is called evacuation. Close the valve on the refrigerant cylinder and connect the charging hoses to the cylinder and the system's service port.
Step 2: Connect Gauges
Connect the low-pressure gauge to the suction service port and the high-pressure gauge to the discharge service port. Open the manifold valves slightly to allow a small amount of refrigerant to purge the air from the hoses.
Step 3: Add Refrigerant Slowly
Turn on the refrigeration system (compressor should run). Slowly open the refrigerant cylinder valve to allow refrigerant to enter the system. Watch the gauges carefully. Add refrigerant until the low-side pressure reaches the manufacturer's recommended charging pressure for the current room temperature.
Step 4: Check Superheat
Use the thermometer to measure the temperature at the evaporator outlet. Calculate superheat by subtracting the saturated temperature (from the low-pressure gauge) from the actual measured temperature. The superheat value should match the system specifications — typically between 5°C and 10°C for most systems.
After charging, commissioning verifies that the system operates correctly:
- Run the system for at least 15 minutes and observe the cooling effect
- Check both high and low pressures against the manufacturer's charts
- Measure the temperature difference between the inlet and outlet air — usually 8°C to 12°C for air conditioners
- Inspect all connections for refrigerant leaks using leak detector or soap solution
- Verify electrical readings — check that the compressor draws the correct current
- Ensure the condenser fan and evaporator fan are running properly
- Check that the unit is level using a spirit level
A small split air conditioner in Arusha is being charged. The outdoor temperature is 30°C. The low-pressure gauge reads 5.5 bar (which corresponds to a saturated temperature of 5°C). The technician measures the evaporator outlet temperature at 12°C.
Calculate the superheat:
Superheat = Actual temperature − Saturated temperature
Superheat = 12°C − 5°C = 7°C
This superheat value of 7°C falls within the normal range of 5°C to 10°C, so the system is properly charged. If the superheat were below 5°C, the system would be overcharged. If above 10°C, it would be undercharged.
| Problem | Signs on Gauges | Possible Cause |
|---|---|---|
| Undercharge | Low suction pressure, frost on evaporator | Refrigerant leak or underfilling |
| Overcharge | High head pressure, poor cooling | Too much refrigerant added |
| Air in system | High suction and head pressure | Evacuation was incomplete |
| Blocked filter | Low suction pressure, ice on filter | Dirty filter or restricted flow |
Charging with refrigerant and commissioning the system are final but critical steps in installing any refrigeration or air conditioning unit. Always evacuate the system first, add the correct amount of refrigerant based on pressure and temperature readings, and then thoroughly test the system during commissioning. Proper charging and commissioning ensure the system runs efficiently, lasts longer, and uses energy wisely.
In Tanzania, refrigeration technicians working in Dar es Salaam, Mwanza, or Dodoma frequently install and service air conditioners in homes, shops, and small businesses. When a new split AC is fitted in a duka (shop), the technician must charge it with the correct amount of R-410A or R-22 refrigerant and commission it — checking pressures, cooling performance, and electrical safety — before handing the unit to the owner. This ensures the AC cools reliably during hot Tanzanian weather, saves electricity, and avoids costly repairs caused by incorrect charging.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
The student should be able to:
- Select tools and equipment
- Read installation drawings
- Prepare machine foundations
- Use safely lifting tackles
- Measure and record required operation parameters
- Clean workplace tools and equipment
- Store tools and equipment
Tathmini ya matokeo
The chilling plant installed and documentation conform to technical specifications
Tathmini ya maarifa
Knowledge Evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Perform machinery alignment
- Anchor equipment
Principles: The student should explain the principles of:
- Heat transfer
- Air flow in ducts / pipes
Theories: The student should explain:
- Super heating and sub-cooling
- Refrigeration cycle
- Storage temperature requirements of different commodities
- Classification of refrigerants
Circumstantial knowledge:
Detailed knowledge about:
- Construction site safety management
- Environmental regulations
Swali
What is the first step a technician must take before charging a refrigeration system with refrigerant?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado