Mada za sehemu hiiPerforming metal cuttingMada 4
- Cutting flat bars
- Cutting metal sheets
- Cutting round bars
- Cutting hollow material
Cutting Flat Bars
Cutting flat bars is a fundamental metalworking skill in refrigeration and air conditioning work. Flat bars are rectangular metal pieces with a uniform cross-section, commonly used to make brackets, supports, frames, and various structural components in cooling systems and equipment.
The following tools are needed for cutting flat bars:
- Hacksaw (with frame and blade)
- Steel rule
- Scriber
- Centre punch
- Hammer
- Vise (to clamp the workpiece)
- Protective safety gear (goggles, gloves, safety boots, overall)
A hacksaw is a hand tool designed specifically for cutting metal. It consists of three main parts: the blade with sharp teeth, the frame, and the handle.
Types of Hacksaw Frames
- Solid frames — accept only one standard blade length
- Adjustable frames (flat type) — can fit different standard blade lengths (250mm or 300mm)
For best results, use a rigid frame as it provides better grip and control during cutting.
Types of Hacksaw Blades
- All-hard blades — the entire blade is hardened, making it brittle but durable for straight cuts
- Flexible blades — only the teeth are hardened, allowing flexibility for curved cuts
Blade Pitch
The pitch refers to the distance between adjacent teeth. Blade selection depends on the material:
- 14 teeth per 25mm — coarse pitch for soft materials like aluminium
- 18 teeth per 25mm (1.4mm) — the most common pitch for general-purpose cutting
- 24 or 32 teeth per 25mm — fine pitch for hard materials and thin sections (such as sheet metal or pipes)
Important rule: When cutting thin materials or pipes, use a fine enough pitch so that at least two teeth are always engaged in the material.
- Never test blade sharpness with your finger — you will get cut
- Store the hacksaw where teeth cannot be accidentally grasped
- The burr (rough edge) left on the cut surface is very sharp and can cause serious cuts
- Never wipe metal chips away with your bare hand
- Always cut on the side of the vice away from your body — if the blade snaps, your hands will slip away from the vice, not into it
Step 1: Select the Appropriate Blade
Choose a hacksaw blade based on the material and thickness of the flat bar. For mild steel flat bars (commonly used in refrigeration work), use an 18-teeth-per-25mm blade.
Step 2: Fit the Blade Correctly
- Hook the blade over the pins at both ends of the frame
- Ensure the teeth point away from the handle (the saw cuts only on the forward stroke)
- Tighten using the wing nut — turn it two full turns after taking up initial tension
- Note: A new blade stretches slightly and should be tightened again after the first few strokes
Step 3: Mark the Workpiece
- Use a steel rule and scriber to measure and mark the cutting line on the flat bar
- Use a centre punch to create a small starting dent at the beginning of the cut line
Step 4: Clamp the Workpiece
Secure the flat bar firmly in a vice. Position the cutting line as close to the vice jaw as possible to minimize vibration (chatter) that could break the blade.
Step 5: Begin Cutting
- Use your thumb to guide the blade into the starting position
- Apply constant forward pressure to keep the cut even
- Use the whole length of the blade
- Maintain a steady pace of about 40 to 50 strokes per minute
- Lift the saw slightly on the return stroke to release pressure
- Support the piece with your hand as it nears completion to prevent it from dropping
Step 6: Complete and Finish
- Release the blade tension before storing the hacksaw (this prevents the frame from losing its spring)
- File any sharp burrs left on the cut edge
Task: A mild steel flat bar measures 5mm × 70mm × 200mm. Cut it into five equal pieces using a hacksaw.
Solution:
- Calculate the length of each piece: 200mm ÷ 5 = 40mm per piece
- Mark the flat bar: Use a steel rule and scriber to mark four lines at 40mm, 80mm, 120mm, and 160mm from one end
- Select the blade: Use an 18-teeth-per-25mm hacksaw blade (suitable for mild steel)
- Clamp and cut: Secure in vice and cut along each marked line following the proper procedure
- Finish: File any burrs and check that each piece is approximately 40mm long
- Using the wrong blade pitch for the material
- Applying too much pressure, which can break the blade
- Cutting too fast (causes heat that blunts the teeth)
- Not using the full blade length (wears out one section faster)
- Cutting on the wrong side of the vice (safety hazard)
In Tanzania, refrigeration and air conditioning technicians often fabricate custom brackets and mounting frames from flat bars to install split air conditioners in homes, shops, and offices. For example, when installing a 1.5 HP split air conditioner in a Dar es Salaam shop, a technician may need to cut a flat bar to create a sturdy wall-mounted bracket that supports the outdoor unit, ensuring it is securely fixed despite the humid coastal climate.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret drawings
- Select proper materials
- Mark out the work piece
- Cut pieces to the required shapes and sizes
- Check for accuracy
- Clean tools, work piece and workplace
- Store tools and equipment safely
Tathmini ya matokeo
Cut pieces of material conform to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to cut work pieces in different shapes
Principles: The student should explain the principals involved in:
- Taking measurements
- Marking work piece
- Cutting process
Theories: The student should explain:
- Different types of materials and their properties
- Explain application of different materials
- Proper use of cutting tools and equipment
Detailed knowledge about:
- Safety precautions when performing cutting process
- Safe handling of working tools and equipment
Swali
Which of the following is the most common blade pitch used for general-purpose cutting with a hacksaw?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado