Mada za sehemu hiiPerforming metal cuttingMada 4
- Cutting flat bars
- Cutting metal sheets
- Cutting round bars
- Cutting hollow material
Cutting Round Bars
Cutting round bars is a fundamental metalworking skill in refrigeration and air conditioning work, where round bars of various metals are cut to specific lengths for making brackets, supports, and component fittings. This skill uses the same principles as straight sawing but requires specific techniques to ensure accurate, clean cuts on cylindrical metal stock.
The following tools are required:
- Hacksaw – with adjustable frame (250mm or 300mm blade)
- Hacksaw blades – 18 teeth per 25mm (1.4mm pitch) for general use
- Steel rule – for measuring
- Scriber – for marking
- Centre punch – for starting the cut
- Vice – for clamping the workpiece
- Hammer – for tapping centre punch
All-hard blades: The entire blade is hardened. These are rigid and used for straight cuts.
Flexible blades: Only the teeth are hardened, allowing the blade to bend. These are useful when cutting along curved lines but can also help when cutting round bars where the blade must follow the curved surface.
When cutting round bars, the blade pitch is important:
| Material Type | Teeth per 25mm | Pitch |
|---|---|---|
| Soft metals (aluminium, copper) | 14 teeth | 1.8mm (coarse) |
| Mild steel (common in refrigeration) | 18 teeth | 1.4mm (medium) |
| Hard metals, thin sections | 24-32 teeth | Fine pitch |
For typical round bars used in refrigeration work (such as 6mm or 10mm diameter mild steel rods), use an 18-teeth-per-25mm blade.
Step 1: Interpret the Drawing
Read the working drawing to determine the required length and diameter of the round bar to be cut.
Step 2: Mark the Workpiece
Using a steel rule and scriber, measure and mark the cutting line on the round bar. For round bars, mark all around the circumference at the required length.
Step 3: Centre-Punch the Mark
Place a centre punch on the marked line and tap lightly with a hammer to create a small indentation. This starting point prevents the saw blade from slipping when beginning the cut.
Step 4: Clamp the Workpiece
Secure the round bar firmly in a vice. Position it so the cutting line is close to the vice jaws—this reduces vibration and blade breakage. For round bars, you may need to use a piece of wood or soft metal to protect the bar from vice marks.
Step 5: Fit the Hacksaw Blade
- Mount the blade with teeth pointing away from the handle
- The blade cuts only on the forward stroke
- Tighten with the wing nut until taut, then give two more full turns
- Do not overtighten—excessive tension can break the pins or bend the frame
Step 6: Begin the Cut
- If right-handed, stand on the right-hand side of the vice
- Use your left thumb to guide the blade into the centre punch mark
- Start with light pressure on the forward stroke
Step 7: Maintain Steady Cutting
- Apply even pressure on each forward stroke
- Use the full length of the blade (40-50 strokes per minute)
- Lift slightly on the return stroke to reduce wear
- For round bars, rotate the bar slightly as you cut to maintain an even cut around the circumference
Step 8: Complete the Cut
As the blade nears completion, support the cutoff piece with your hand to prevent it from dropping and causing injury or damage.
Step 9: Finish and Clean
- File any burrs or sharp edges left on the cut surface
- Remove all sharp edges for safety
- Clean the work area and return tools
-
Always wear safety goggles when cutting
- Metal chips can fly into eyes
-
Wear gloves to protect hands from sharp edges
- The burr on cut surfaces is extremely sharp
-
Do not test blade sharpness with your finger
- You will get cut
-
Cut on the correct side of the vice
- Right side for right-handed persons
- If the blade breaks, your hands will slip away from the vice
-
Do not wipe chips away with your bare hand
- Use a brush or cloth
-
Release blade tension before storing the hacksaw
- This preserves the frame's spring
Task: Cut a 10mm diameter mild steel round bar into three equal pieces of 80mm each.
Procedure:
- Measure 240mm total length on the round bar using a steel rule
- Mark three lines at 80mm intervals using a scriber
- Centre-punch each mark
- Clamp the bar in the vice
- Select an 18-teeth-per-25mm hacksaw blade (suitable for mild steel)
- Cut at the first mark, rotating the bar slightly with each stroke to maintain a circular cut
- Measure and cut the second and third marks similarly
- File any burrs from all cut ends
- Verify each piece is approximately 80mm long
| Problem | Cause | Solution |
|---|---|---|
| Blade breaks frequently | Too much pressure, wrong pitch, or blade not tight enough | Apply lighter pressure, select correct pitch, check tension |
| Cut is not straight | Uneven pressure, blade not perpendicular | Maintain even pressure, keep blade at 90° to work |
| Blade sticks | Cut becoming narrow, insufficient lubrication | Rotate workpiece, use appropriate blade pitch |
| Cut surface is rough | Dull blade or wrong tooth pitch | Replace blade, select finer pitch |
In Tanzania, cutting round bars is essential for refrigeration and air conditioning technicians who fabricate mounting brackets for split-type air conditioners commonly installed in homes, offices, and shops in Dar es Salaam, Arusha, and other cities. A technician may need to cut a 10mm steel rod to create a support bracket for securing an outdoor condenser unit to a wall, ensuring the air conditioner is safely mounted despite Tanzania's hot climate conditions.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret drawings
- Select proper materials
- Mark out the work piece
- Cut pieces to the required shapes and sizes
- Check for accuracy
- Clean tools, work piece and workplace
- Store tools and equipment safely
Tathmini ya matokeo
Cut pieces of material conform to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to cut work pieces in different shapes
Principles: The student should explain the principals involved in:
- Taking measurements
- Marking work piece
- Cutting process
Theories: The student should explain:
- Different types of materials and their properties
- Explain application of different materials
- Proper use of cutting tools and equipment
Detailed knowledge about:
- Safety precautions when performing cutting process Safe handling of working tools and equipment
Swali
Which of the following is the correct hacksaw blade specification for cutting typical mild steel round bars used in refrigeration work?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado