Mada za sehemu hiiConstructing capacitive circuitsMada 4
- Building single capacitor circuits
- Building series circuits
- Building parallel circuits
- Building combined series parallel circuits
Single Capacitor Circuits
A single capacitor circuit is a basic electrical circuit that contains one capacitor connected together with a power source (battery), a switch, connecting wires, and often a resistor. This type of circuit is used to store electrical energy in an electric field and is fundamental in refrigeration and air conditioning systems where capacitors help start and run electric motors.
1. Power Source (Battery)
The battery provides the electrical potential difference (voltage) needed to push charges onto the capacitor's plates. In laboratory settings, a 9V battery or a low-voltage DC power supply is commonly used.
2. Capacitor
A capacitor is an electronic component that stores electrical energy in an electric field. It consists of two parallel conductive plates separated by an insulating material called a dielectric. When connected to a battery, one plate accumulates positive charge while the other accumulates equal negative charge.
3. Resistor
The resistor limits the flow of current in the circuit, protecting the capacitor from damage and controlling the rate at which the capacitor charges. Without a resistor, a capacitor can draw very high initial current that may damage components.
4. Switch
The switch controls whether the circuit is complete (ON) or broken (OFF). It allows you to start and stop the charging process of the capacitor.
5. Connecting Wires
Wires provide the conductive path that connects all components together to form a complete circuit.
Before building any circuit, always follow these safety rules:
- Wear safety goggles when cutting or stripping wires
- Wear overalls to protect your clothing
- Work on a clean, dry work bench
- Ensure your hands are dry when handling electrical components
- Never connect a capacitor directly to a battery without a resistor
- Use insulated tools (combination pliers, long nose pliers) when working with live circuits
Step 1: Plan Your Circuit
Draw a circuit diagram on paper first. A single capacitor circuit typically looks like this:
Battery→Switch→Resistor→Capacitor→Battery
Step 2: Gather Components
Collect all required components: proto board, battery (9V), capacitor (e.g., 100µF electrolytic), resistor (e.g., 1kΩ), switch, connecting wires, and multimeter.
Step 3: Prepare the Proto Board
Place the proto board on your work bench. Ensure it is clean and dry.
4. Connect the Resistor
Using the long nose pliers, insert the resistor into the proto board. The resistor can be connected in either direction (it is not polarity-sensitive).
Step 5: Connect the Capacitor
Insert the capacitor carefully into the proto board. Important: For electrolytic capacitors, observe the polarity markings (+ and -). The positive lead must connect to the positive side of the circuit. Reversing an electrolytic capacitor can cause it to explode.
Step 6: Connect the Switch
Insert the switch into the proto board in an open (OFF) position.
Step 7: Connect the Battery
Connect the battery holder or DC power supply to the circuit using wires. Connect the positive terminal of the battery to one side of the switch.
Step 8: Complete the Wiring
Use the diagonal cutting pliers to cut wires to appropriate lengths. Strip the insulation from the ends using the electrician knife. Connect all components according to your circuit diagram, ensuring all connections are secure.
Step 9: Verify the Circuit
Before closing the switch, double-check all connections against your circuit diagram.
Problem: A 100µF capacitor is connected in series with a 10kΩ resistor across a 12V DC supply.
Calculate:
- The time constant of the circuit
- The voltage across the capacitor after one time constant
Solution:
The time constant (τ) is given by: τ=R×C
Converting to standard units:
- R = 10kΩ = 10,000Ω
- C = 100µF = 100 × 10⁻⁶F = 10⁻⁴F
τ=10,000×10−4=1 second
After one time constant, a capacitor charges to approximately 63.2% of the supply voltage: Vc=12V×0.632=7.58V
Therefore, after 1 second, the voltage across the capacitor will be approximately 7.58V.
After building the circuit:
- Close the switch (ON position)
- Use a digital multimeter set to DC voltage to measure the voltage across the capacitor terminals
- Observe how the voltage increases over time until it reaches the battery voltage
- Record your observations at regular intervals
In Tanzania, single capacitor circuits are used in:
- Starting capacitors for single-phase motors in refrigerators and air conditioners
- Timing circuits in electrical appliances
- Energy storage in flash circuits for photography
- Filter circuits in radio receivers and audio equipment
In many Tanzanian homes and shops, refrigeration units (such as those found in dukas and restaurants) use single-phase capacitor-run motors. When these motors fail to start, the problem is often a faulty start or run capacitor. Understanding how single capacitor circuits work allows a technician to test these components using a multimeter, identify faulty capacitors, and replace them — keeping food fresh and businesses running. For example, a small restaurant in Dar es Salaam experiencing a refrigerator that won't start may need a 45µF run capacitor replaced, which costs approximately TSh 15,000 to 25,000 at local electronics shops.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret the given circuit diagram of a capacitive circuit
- Identify equipment, tools and material required
- Prepare capacitors and wires for termination
- Build a single capacitor circuit
- Solder the built circuits
- Test the built circuits
- Clean work area, tools and equipment
- Store tools, equipment and the materials
Tathmini ya matokeo
The capacitive circuits constructed conform to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Construct capacitive circuits
- Measure capacitive reactance of the built circuit
- Identify different types of capacitors (Polarized, non-polarized)
- Calculate the value capacitance
Principles: The student should explain the principles of:
- Constructing single capacitive circuits
- Carrying out measurement of capacitance and voltage in single capacitive circuit
Theories: The student should explain:
- Symbols for capacitor
- Types of capacitors
- The application of the various types of capacitive circuit
Detailed knowledge about:
- Safety precautions in capacitive circuits Safe handling of working tools, equipment
Swali
What is the main function of the resistor in a single capacitor circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado