Mada za sehemu hiiConstructing resistive circuitsMada 4
- Building single resistor circuit
- Building series circuit
- Building parallel circuit
- Building series parallel circuit
Series-Parallel Resistor Circuits
A series-parallel circuit is a combination of two or more resistors connected in such a way that some are arranged one after another (in series) while others are placed side by side (in parallel). This type of circuit is commonly found in refrigeration and air conditioning equipment where different components require different voltage or current levels to operate properly.
In a series circuit, components are connected end-to-end, forming a single path for current to flow. The same current passes through each component, but the voltage is divided among them.
Key characteristics:
- Current is the same at all points in the series
- Voltage divides across each component
- If one component fails (opens), the entire circuit stops working
In a parallel circuit, components are connected across the same two points, creating multiple paths for current to flow. Each component receives the same voltage.
Key characteristics:
- Voltage is the same across all parallel branches
- Current divides among the parallel branches
- If one component fails, the other branches continue working
When you combine both arrangements, you get a series-parallel circuit. Follow these steps to build one:
Step 1: Plan Your Circuit
Decide which resistors will be in series and which will be in parallel. A common approach is to:
- Connect some resistors in parallel first
- Then connect that parallel group in series with other components
Step 2: Gather Components
For a basic series-parallel circuit, you need:
- A battery (power source)
- Two or more resistors of different values
- Connecting wires
- A switch (to control the circuit)
- A multimeter (to measure voltage and current)
Step 3: Connect the Parallel Section first
Place resistors side by side between the same two points. Use your proto board or solder connections neatly.
Step 4: Connect the Series Section
Add the parallel group in series with the battery, switch, and any remaining resistors.
Step 5: Test the Circuit
Close the switch and use your multimeter to:
- Measure total voltage across the battery
- Measure voltage drops across each resistor
- Verify that current flows through all branches
Problem: Build a circuit where a 12V battery supplies power to two resistors: R1 = 100Ω connected in parallel with R2 = 200Ω, and this parallel group is connected in series with R3 = 50Ω.
Solution:
-
First, calculate the equivalent resistance of the parallel section: Rparallel=R1+R2R1×R2=100+200100×200=30020000=66.7Ω
-
Add the series resistor: Rtotal=Rparallel+R3=66.7+50=116.7Ω
-
Calculate total current from the battery: Itotal=RtotalV=116.712=0.103A≈103mA
This current flows through R3 and splits at the parallel junction between R1 and R2.
In refrigeration and air conditioning systems, series-parallel circuits allow technicians to:
- Provide different voltage levels to different components
- Create backup paths so that if one component fails, others keep working
- Control how much current flows to sensitive components
- Design circuits that are both reliable and efficient
When building circuits, always:
- Wear safety goggles and electrical gloves
- Work on a proper work bench
- Never touch bare wires while the circuit is powered
- Use insulated tools
- Check all connections before turning on the power
If your circuit does not work:
- Check all wire connections are secure
- Verify the switch is properly closed
- Use the multimeter to check each resistor is functioning
- Make sure the battery has sufficient charge
In Tanzania, refrigerator and air conditioning repair technicians regularly encounter series-parallel circuits when diagnosing faulty equipment. For example, when a split AC unit stops cooling, a technician in Dar es Salaam might find that the fan motor (connected in parallel with the compressor) still runs while the compressor (connected in series) has failed — this series-parallel arrangement means one component can fail without stopping the entire system, helping technicians quickly identify which part needs replacement.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret given circuit drawing of the single resistor circuit
- Identify equipment, tools and material required
- Prepare resistors and wires for termination
- Build a series parallel circuit
- Solder the built circuits
- Test built circuits
- Clean work area, tools and equipment
- Store tools, equipment and materials
Tathmini ya matokeo
The resistive circuits constructed conform to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure the electrical quantities of the built circuit resistors
- Read resistor values by colour codes
- Calculate the value of resistance in series parallel circuit
Principles: The student should explain principle of:
- Constructing resistive circuits
- Carrying out measurements in resistive circuits
Theories: The student should explain:
- Types of resistors
- Electrical symbols used to draw the resistive circuit
- The series-parallel resistive circuit and its behaviour
- The application of the various types of resistive circuits
- The use of various tools and equipment
Detailed knowledge about:
- Safe handling of working tools and equipment
- Awareness of Electrical hazards
- First aid
Swali
What happens to the current in a series circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado