Mada za sehemu hiiConstructing resistive circuitsMada 4
- Building single resistor circuit
- Building series circuit
- Building parallel circuit
- Building series parallel circuit
A single resistor circuit is the simplest type of resistive circuit. It consists of a power source (like a battery), a resistor, connecting wires, and optionally a switch to control the flow of current. In refrigeration and air conditioning work, understanding how to build and measure such circuits is essential because resistors are used in temperature controls, fan motors, and compressor circuits.
The circuit is made up of four main components:
- Power source (Battery) — provides the electrical energy (voltage) that pushes current through the circuit. Common batteries used in labs are 9V or 12V DC batteries.
- Resistor — limits the flow of current to a safe value. The resistance is measured in ohms (Ω) and is indicated by coloured bands on the resistor body.
- Connecting wires — carry electric current from the battery, through the resistor, and back to the battery. Wires should have good insulation and proper connectors.
- Switch — controls whether the circuit is ON or OFF. When the switch is closed, current flows; when open, current stops.
- Plan the circuit layout on the proto board or breadboard, making sure all components can be connected easily.
- Identify the resistor value using the colour code. For example, a resistor with brown, black, and red bands is a 1,000 Ω (1 kΩ) resistor.
- Connect one end of the resistor to the positive terminal of the battery using a wire.
- Connect the other end of the resistor to one terminal of the switch using another wire.
- Connect the other switch terminal back to the negative terminal of the battery with a final wire.
- Check all connections to ensure they are tight and there are no loose ends.
- Close the switch to complete the circuit and allow current to flow.
- Measure the voltage and current using a multimeter. Set the multimeter to DC voltage to measure across the battery, and to DC current (in series) to measure the circuit current.
A student builds a single resistor circuit using a 12V battery and a 470 Ω resistor.
Calculate the current flowing through the circuit.
Using Ohm's Law:
I=RV
Where:
- V = 12V (battery voltage)
- R = 470 Ω (resistance value)
I=47012=0.0255 A=25.5 mA
The current flowing through the circuit is approximately 25.5 milliamps (mA).
- Voltage measurement: Connect the multimeter probes across the battery (positive to positive, negative to negative). The reading should be close to 12V.
- Current measurement: Break the circuit at any point and insert the multimeter in series. The reading should match the calculated value from Ohm's Law.
If the measured values differ from expected values, check for:
- Loose wire connections
- Faulty battery or resistor
- Wrong multimeter settings
- Always wear safety goggles and electrical gloves when working with live circuits.
- Ensure the work bench is clean and free of metallic objects.
- Use insulated tools like combination pliers and long-nose pliers.
- Never touch bare wires while the circuit is connected to a power source.
- Make sure the soldering iron is placed on its stand when not in use.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret given circuit drawing of the single resistor circuit
- Identify equipment, tools and material required for: Make single resistor circuit and wires for termination
- Build a single resistor circuit
- Solder the built circuits
- Test built circuits
- Clean work area, tools and equipment
- Store tools, equipment and materials
Tathmini ya matokeo
The resistive circuits constructed conform to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure the electrical quantities in single resistor circuit resistors
- Read resistor values by colour codes
Principles: The student should explain principle of:
- Constructing resistive circuits
- Carrying out measurements in resistive circuits
Theories: The student should explain:
- Types of resistors
- Electrical symbols used to draw the resistive circuit
- The application of the various types of resistive circuits
- The use of various tools and equipment
Detailed knowledge about:
- Safe handling of working tools and equipment
- Awareness of Electrical hazards
- First aid
Swali
Which of the following is NOT a component of a single resistor circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado