Mada za sehemu hiiConstructing resistive circuitsMada 4
- Building single resistor circuit
- Building series circuit
- Building parallel circuit
- Building series parallel circuit
A series circuit is a single path through which electric current flows from the power source, through each component, and back to the source. When you connect components one after another in a single loop, you build a series circuit — the same current passes through every part of the circuit.
In a series circuit:
- All components are connected end-to-end in one continuous loop
- The same electric current flows through each component
- If one component fails or is disconnected, the entire circuit stops working
- The total resistance is the sum of all individual resistances
To build a basic series resistor circuit, you need these main components:
- Battery — provides the electromotive force (voltage) that pushes current through the circuit
- Resistor — limits the current flow and reduces voltage to a safe level for other components
- Wires — connect the components and provide a path for current to flow
- Switch — controls whether the circuit is complete (ON) or broken (OFF)
Additional tools used include a soldering iron, electrician knife, combination pliers, and multimeter for testing.
-
Plan your circuit — Decide on the voltage of your battery and the resistance value you need. Remember: higher resistance means less current flows.
-
Prepare the wires — Use the electrician knife to strip about 1 cm of insulation from each end of the connecting wires.
-
Connect the battery — Attach one wire to the positive terminal (+) and another wire to the negative terminal (−) of the battery.
-
Add the resistor — Connect the resistor in series by joining one of its leads to the wire from the positive terminal using long-nose pliers. If needed, solder the connection with the soldering iron.
-
Include the switch — Connect the switch in series with the rest of the circuit. When the switch is open (OFF), the circuit is broken; when closed (ON), current flows.
-
Complete the loop — Connect the free end of the resistor to one terminal of the switch, and the other terminal of the switch back to the negative terminal of the battery.
-
Test the circuit — Use a multimeter to measure voltage across each component and verify the circuit is working properly. Always wear safety goggles and electrical gloves while testing.
A refrigeration technician needs a simple series circuit with a 9V battery and a 220Ω resistor to power a small indicator light.
Given:
- Voltage (V) = 9V
- Resistance (R) = 220Ω
Find the current flowing through the circuit.
Using Ohm's Law: I=RV=220Ω9V=0.041A
The current flowing through the series circuit is approximately 41 milliamps (mA).
In this series circuit, the same 41 mA current flows through the battery, the resistor, and the indicator light. If another resistor of 100Ω were added in series, the total resistance would become: Rtotal=220Ω+100Ω=320Ω And the new current would be: I=320Ω9V=0.028A
Series resistor circuits are used for:
- Current limiting — Resistors limit current to protect sensitive components like LED indicator lights
- Voltage division — Series resistors divide voltage to provide different voltage levels to various parts of a control circuit
- Sensor circuits — Temperature sensors in refrigeration units often use series resistor configurations
- Starting circuits — Some compressor motor starting circuits use series resistors to reduce initial current
When your series circuit does not work:
- Check all connections are secure and properly soldered
- Verify the switch is in the ON (closed) position
- Use the multimeter to check that the battery still has voltage
- Test each component individually to find a faulty part
In Tanzania, refrigeration technicians in Dar es Salaam, Arusha, and other cities use series resistor circuits when installing or repairing split air conditioners and commercial refrigeration display cabinets. For example, when wiring the control board of a cold room, a technician may connect resistors in series with the thermostat and fan motor to ensure the fan runs only after the compressor has operated for a set time, protecting the equipment from damage — a common practice in small businesses like supermarkets and fish processing facilities across the country.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Interpret given circuit drawing of Build series circuit
- Identify equipment, tools and material required
- Prepare resistors and wires for termination
- Build series circuit
- Solder the built circuits
- Test built circuits
- Clean work area, tools and equipment
- Store tools, equipment and materials
Tathmini ya matokeo
The series circuits constructed conform to technical specifications
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The student should explain how to:
- Measure the electrical quantities of the built series circuit
- Read resistance values by
- Calculate the value of resistance in series
Principles: The student should explain principle of series circuit
Theories: The student should explain:
- Types of circuit
- Electrical symbols used to draw the series circuit
- The series resistive circuit and its behaviour
- The application of the various types of resistive circuits
- The use of various tools and equipment
Detailed knowledge about:
- Safe handling of working tools and equipment
- Awareness of Electrical hazards
- First aid
Swali
What is a series circuit?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado