Mada za sehemu hiiMeasuring electric quantitiesMada 5
- Measuring voltage in the circuit
- Measuring current in the circuit
- Measuring resistance in the circuit
- Carrying out insulation test
- Carrying out earthing test
Measuring Voltage in Electric Circuits
Voltage is the electrical pressure or force that pushes electric charges (electrons) through a conductor in a circuit. It is measured in volts (V). Think of voltage like water pressure in a pipe — the higher the pressure, the more forcefully the water flows. In an electrical circuit, a higher voltage pushes electrons more strongly through the wires.
A voltage source such as a battery or power supply provides the "push" that makes electrons move. In refrigeration and air conditioning systems, voltage is crucial because compressors and fans require specific voltages to operate safely and efficiently.
A voltmeter is an instrument used to measure the voltage difference between two points in a circuit. Modern digital multimeters (also called multimeters) can measure voltage, as well as current and resistance.
Types of Voltmeters
- Analog voltmeter: Uses a moving needle to show voltage on a scale
- Digital voltmeter/multimeter: Shows the voltage reading as a number on a screen
For most practical work in refrigeration and air conditioning, we use a digital multimeter because it is easy to read and can measure both AC (alternating current) and DC (direct current) voltages.
Important rule: A voltmeter must always be connected in parallel (across) the component whose voltage you want to measure.
Steps to Connect a Voltmeter
- Turn off the power before connecting the voltmeter.
- Identify the two points in the circuit between which you want to measure voltage.
- Connect the red lead of the voltmeter to the point of higher potential (positive side).
- Connect the black lead to the point of lower potential (negative side or ground).
- Select the correct voltage range on the multimeter (DCV for battery, ACV for mains supply).
- Turn on the power and read the voltage display.
Parallel Connection
When you connect a voltmeter in parallel, it does not affect the flow of current in the circuit. The voltmeter has very high internal resistance, so it draws almost no current. This is why it can be placed across a component without changing the circuit's behavior.
When reading a voltmeter or multimeter:
- DC voltage: Look for the DCV setting. This is used for batteries, power supplies, and low-voltage systems.
- AC voltage: Look for the ACV setting. This is used for mains electricity (like the 230V wall outlets in Tanzania).
Always start with a higher voltage range if you are unsure of the expected voltage. You can switch to a lower range for a more accurate reading.
A student builds a simple circuit with a 9V battery connected to a resistor. The student wants to measure the voltage across the resistor.
Step 1: The student turns off the circuit and connects the multimeter leads in parallel across the resistor (red to the side connected to the battery's positive terminal, black to the other side).
Step 2: The student selects the 20V DC range on the multimeter.
Step 3: The multimeter displays 6.2V.
Question: What is the voltage drop across the resistor?
Answer: The voltage across the resistor is 6.2V. In a series circuit, the sum of voltage drops equals the source voltage. Therefore, if the battery provides 9V and the resistor drops 6.2V, the remaining voltage drop across any other components would be 9V−6.2V=2.8V.
- Always wear safety boots and overalls when working with electrical circuits.
- Use HT safety gloves when working with high voltages.
- Never connect a voltmeter in series (it will not work and could damage the meter).
- Ensure the multimeter is set to the correct voltage type (AC or DC) before measuring.
- If unsure of the voltage level, start with the highest range and decrease as needed.
- Keep the test leads clean and in good condition.
- Ensure good contact between the probes and the circuit points.
- Avoid touching the metal parts of the probes while measuring live circuits.
- Check the battery level in your multimeter regularly.
In Tanzania, technicians working with air conditioning units in Dar es Salaam or Arusha regularly use multimeters to measure the voltage across compressor terminals. For example, if a split AC unit is not cooling properly, a technician would measure the supply voltage at the wall outlet (should be around 230V AC) and then check the voltage across the compressor's run capacitor terminals. If the reading is significantly lower than expected, this could indicate a power supply problem or a faulty compressor, helping the technician diagnose the fault correctly before repairs.
Jinsi utakavyotathminiwaTathmini ya mchakato · Tathmini ya matokeo · Tathmini ya maarifa
Tathmini ya mchakato
- Determine component values
- Connect simple electric circuits
- Perform soldering
- Measure voltage in the circuit
- Clean workplace and tools
- Store tools, materials and equipment
Tathmini ya matokeo
Electrical quantities measured conform to IEEE standards
Tathmini ya maarifa
Knowledge evidence:
Detailed knowledge of:
Method used: The students should explain how to:
- Measure component values
- Read colour codes
- Calculate electric quantities
- Determine the values of components using colours codes
- Measure voltage and current
Principles: The student should explain principle of:
- Connecting electrical circuits in
- Taking voltage measurements in the circuit
Theories: The student should explain:
- Different component ratings
- Types of electric circuit connections
- Verification of electric rules and laws
- Importance of component ratings
- Types and uses of measuring and testing instruments
Detailed knowledge about:
- Safe handling of working tools Safe handling of measuring instruments
Swali
What is the unit used to measure voltage?
Ingia ili kuwasilisha jibu lako na lihesabiwe katika umahiri wako.
Ingia ili kufanya mazoeziMwalimu
Umekwama? Niulize chochote kuhusu mada hii.
Ingia ili kumuuliza Mwalimu wa AI wa Sonza kuhusu swali hili.
Ingia ili kuulizaMajadiliano
Hakuna maswali bado